Inhaltsverzeichnis
Werbung
– Protection class: III
– IP rating: IP 44
– Temperature range: -20 °C to +40 °C
Short
194 x 628 x 188 mm
Medium
194 x 808 x 188 mm
Long
194 x 1178 x 188 mm
Technical specifications for rechargeable
battery
– Nanophosphate
®
high-power lithium-ion
rechargeable battery, cadmium-free LiFePO
– Can be recharged at any time without shortening
battery lifespan.
– Automatic recharging by solar panel.
– Can be recharged using charging adapter at
micro USB socket (5 V).
– Can be replaced by the manufacturer or
qualified electricians.
– Rechargeable battery capacity: 2500 mAh
– Max. lighting duration:
60 days at 20 switching operations a night.
– Micro USB charging socket: 5 V, 1 A max.,
can be used in all three programmes.
Recharging time depends on the site of installa-
tion (direct sunlight). Expect charging to take many
times longer in winter or on rainy days.
4. Installation
• Check all components for damage.
• Do not use the product if the solar panel or
LED panel is damaged.
Operating reliability will be limited if the product is
used in adverse conditions (e.g. installed in shade
or behind glass, solar panel not facing the right
direction)
• Choose an appropriate site with plenty of sun-
light for installing the solar panel (facing south).
• Avoid shade from porches, overhanging roofs or
trees.
• Pay attention to detection reach (Ill. 4.1).
• Assemble baseplate and profile (Ill. 4.2).
• loosely screw into place and then tighten screws
alternately on completing installation.
• Mark drill holes (Ill. 4.3).
• Drill holes and fit rawl plugs (Ill. 4.4).
• Screw baseplate to the standing surface
(Ill. 4.4).
• Remove light holder (Ill. 4.5).
• Make settings (Ill. 4.6).
➔ "5. Operation"
• Screw light holder to SensorLight (Ill. 4.7).
• Mount SensorLight on profile (Ill. 4.8).
• Aim LED panel with motion detector in the right
• direction (Ill. 3.4).
• Aim solar panel to get the strongest sunlight for
the longest time possible (Ill. 3.4).
• Check compass (for south-facing position)
(Ill. 3.4).
5. Operation
.
4
Before using for the first time
• Activate light by setting the programme selector
switch to P2.
The light stays in test mode for one minute
before it starts to work in programme P2.
Test mode
During the test sequence the light works in
daytime mode.
On detecting movement, the light switches ON
for 1 minute with a stay-ON time of 10 sec. irre-
spectively of light-level setting. The programme
is automatically activated after this time elapses.
The red LED stays ON all the time in test mode.
Setting the chosen operating mode by
programme selector switch
– P0: OFF (factory setting).
Loads (LED panel and sensor) are deactivated.
– P1: Sensor mode.
Light only switches ON after receiving a signal
from the motion detector.
– P2: Sensor mode with basic light level.
Light switches ON after receiving a signal from
the motion detector.
Light permanently ON in the morning and
evening hours at reduced basic light level.
Stay-ON time and brightness
– Stay-ON time is determined when the light is
used for the first time.
– During the first night, basic lighting is switched
OFF in the morning in programme 2.
– Stay-ON time and brightness can be automati-
cally matched to ambient conditions, e.g. stay-
ON time is longer in summer than it is in winter.
– Basic lighting level provides night-time illumina-
tion at approx. 3% light output. Light is switched
to maximum output when movement is identified
in the detection zone. The light then returns to
basic lighting level (approx. 3%).
The period basic lighting is provided for is
matched to ambient conditions. Using basic
– 10 –
lighting reduces light availability. If it is not need-
ed, it is recommended to switch it OFF (P1) to
ensure lighting availability in less sunny periods.
Charging the battery manually
The red LED in the motion detector flashes if
battery capacity is too low (e.g. in poor weather).
The battery can be recharged with a standard
micro USB charging adapter (not included). Battery
recharging can take up to 6 hours.
Risk of damage to property from penetrating
moisture
When open, the micro USB charging socket (E) is
not protected from the ingress of water.
• Only recharge batteries in a dry room.
• Connect micro USB charging adapter.
– Red LED flashes: charging in progress
The LED may take up to 10 minutes to start
flashing if the battery has run down to very
low level.
– Red LED shows: battery is fully charged.
• Remove micro USB charging adapter.
– Red LED goes out.
Risk of damage to property when light is not
in use
If the light is not used for a prolonged period
(e.g. in storage), the battery may suffer irreparable
damage from exhaustive discharge.
• Set programme selector switch to P0.
• The battery must be on full charge before taking
the light out of service.
• Regularly charge the battery while the light is
not in use.
6. Malfunctions
Red LED flashing in motion detector
– Battery capacity too low.
• Charge battery with micro USB charging
adapter (not included).
Light does not switch ON
– Battery capacity too low.
• C harge battery with micro USB charging
adapter (not included).
– Open or short circuit.
• Check connections.
– Programme selector switch set to P0.
• Set programme selector switch to P1 or P2.
– Detection zone not correctly adjusted.
• Check detection zone.
Light does not switch OFF
– Continued movement within the detection zone.
• Check detection zone.
Light switches ON when it should not
– Uncontrolled movement in the detection zone:
– Wind is moving trees and bushes.
– Cars in the street being detected.
– Sudden temperature changes due to weather
(wind, rain, snow) or air expelled from fans,
open windows.
• Check detection zone.
– Light is swaying (moving) due to gusts of wind or
heavy rain.
• Mount light on a firm surface.
Battery not charging
– Solar panel dirty.
• Clean solar panel with a soft cloth and mild
detergent.
– Solar panel not installed in the best place.
• Check site of installation (as much direct
sunlight as possible).
– It may no longer be possible to recharge the
battery after many years of use.
• Get rechargeable battery changed
(replacement XSolar battery, 3.3 V 2.5 AH,
EAN 007841006488).
• Please send the product well-packed to your
nearest service station. The rechargeable
battery must only be replaced by the manu-
facturer or qualified electricians.
7. Cleaning and Maintenance
The product requires no maintenance.
Regularly checking the product for damage can
prolong its lifespan.
Removing dirt can help to make the product work
longer.
Risk of damage to property
Using the wrong detergent can damage the light.
• Make sure detergent does not harm the surface.
• Clean light with a soft cloth and mild detergent.
If solar panel is dirty or weather has left deposits
on it:
• Clean solar panel with a soft cloth and mild
detergent.
– 11 –
Werbung
Inhaltsverzeichnis
