Technical Data; Machine Data; Noise And Vibration Declaration Statement - Atlas Copco RH 571 Sicherheits- Und Betriebsanleitung

Safety and operating instructions

Technical data

Machine data

Model Part number
RH 571-5L 8311 0301 29
RH 571-5LS 8311 0301 37
RH 572E 8311 0301 78
RH 658L 8311 0302 86
RH 658LS 8311 0302 87
Model
RH 571-5L
RH 571-5LS
RH 572E
RH 658L
RH 658LS

Noise and vibration declaration statement

Guaranteed sound power level Lw according to ISO 3744 in accordance with directive 2000/14/EC.
Sound pressure level Lp according to ISO 11203.
Vibration value A and uncertainty B determined according to ISO 20643. See table "Noise and vibration data"
for the values of A, B, etc.
These declared values were obtained by laboratory type testing in accordance with the stated directive or
standards and are suitable for comparison with the declared values of other tools tested in accordance with
the same directive or standards. These declared values are not suitable for use in risk assessments and values
measured in individual work places may be higher. The actual exposure values and risk of harm experienced
by an individual user are unique and depend upon the way the user works, in what material the machine is
used, as well as upon the exposure time and the physical condition of the user, and the condition of the machine.
We, Atlas Copco Construction Tools AB, cannot be held liable for the consequences of using the declared
values, instead of values reflecting the actual exposure, in an individual risk assessment in a work place situation
over which we have no control.
This tool may cause hand-arm vibration syndrome if its use is not adequately managed. An EU guide to managing
hand-arm vibration can be found at http://www.humanvibration.com/EU/VIBGUIDE.htm
We recommend a programme of health surveillance to detect early symptoms which may relate to vibration
exposure, so that management procedures can be modified to help prevent future impairment.
22
www.CrowderSupply.com • Toll Free: 888-883-5144
Piston bore Stroke length
mm
(in.)
55
(2.16)
55
(2.16)
55
(2.16)
65
(2.56)
65
(2.56)
Air consumption (6 bar)
l/s
3
(foot /min )
39
(83)
39
(83)
37
(78)
58
(123)
58
(123)
© 2010 Atlas Copco Construction Tools AB | No. 9800 0970 90 | 2010-01-01
Overall length
mm mm
(in.) (in.)
60 510
(2.36) 20
60 510
(2.36) 20
60 583
(2.36) 23
59 565
(2.32) 22 1 ⁄
4
59 565
(2.32) 22 1 ⁄
4
Impact rate (6 bar)
Hz
35
33
34
34
34
RH 571, 572, 658
Weight Shank dimension
kg mm
(lb) (in.)
17.8 22 X 108
(39.2) (⅞ x 4¼)
18.9 22 X 108
(41.7) (⅞ x 4¼)
22.8 22 X 108
(50.2) (⅞ x 4¼)
24.0 22 X 108
(52.9) (⅞ x 4¼)
25.0 22 X 108
(55.1) (⅞ x 4¼)
Hole diameter
mm
(in.)
28-34
(1.10-1.34)
28-34
(1.10-1.34)
28-34
(1.10-1.34)
29-40
(1.14-1.57)
29-40
(1.14-1.57)
Original instructions