Reely ROAD MISSION Bedienungsanleitung Seite 84

Programming Rechargeable Battery Type
The appropriate low voltage protection is activated during the initial programming of the
battery type after the initial commissioning of the control unit. For NiCd/NiMH rechargeable
batteries, the shutdown voltage is 4.0 V, for LiPo rechargeable batteries 6.0 V (2 cells).
If you should wish to drive without low voltage protection (we do not recommend this!) you
can select driver profile 5. Then you must complete all further programming again.
• Press and hold the setup button; until the red LED comes on. After it is lit release the setup button. The
red LED flashes, you are now in the setting mode for the rechargeable battery type.
• You can select the rechargeable battery type by briefly pressing the setup button. The flash rhythm of
the red LED changes.
Flash # 1x
Rechargeable battery type NiCd/NiMH
• Hold down the setup button for at least 2 seconds, this saves the setting and the programme mode is
exited.
• If the setup button is not pressed for some 10 seconds, the programming mode is automatically exited
without saving the changes to the settings.
If you select "LiPo" battery, the protective circuit is activated for safety reasons. If a LiPo
battery with 3 or more cells is connected to the speed controller, the red LED flashes and
the drive motor does not start. Immediately disconnect the LiPo battery in such a case. Only
use LiPo batteries with 2 cells.
The protective circuit is not active with NiCd/NiMH batteries. Do not connect NiCd/NiMH
batteries with more than 6 cells to the speed controller! The speed controller and the drive
motor will otherwise be overloaded and destroyed. Guarantee/warranty void!
Switching Reverse On/Off
• Press and hold the setup button; until the blue LED comes on. After it is lit release the setup button. The
blue LED flashes (setting mode for reverse).
• You can switch the reverse mode on or off by briefly pressing the setup button. The flash rhythm of the
blue LED changes.
Flash 1x
Function Reverse mode is turned off
• Hold down the setup button for at least 2 seconds, this saves the setting and the programme mode is
exited.
• If the setup button is not pressed for some 10 seconds, the programming mode is automatically exited
without saving the changes to the settings.
Setting the Brake Performance
As with nearly all other control units, the direct movement of the speed / brake lever on the remote control
from forwards to reverse mode activates the brake. However this control unit allows you to adjust the brake
performance to your requirements. Proceed as follows:
• Press and hold the setup button; until the blue and green LEDs come on. After it is lit release the setup
button. The blue and green LEDs flash (setting mode for brake performance).
• You can select the brake performance by briefly pressing the setup button. The flash rhythm of both LEDs
change.
Flash # 1x 2x
Brake performance 10% 20%
• Hold down the setup button for at least 2 seconds, this saves the setting and the programme mode is
exited.
• If the setup button is not pressed for some 10 seconds, the programming mode is automatically exited
without saving the changes to the settings.
Activating and Setting the Holding Brake
As opposed to normal electric motors, the driveshaft of the brushless motor can be easily turned. Thus the
model does not stay still on a slope. A type of "holding" brake can be activated for this reason. Proceed
as follows:
• Press and hold the setup button; until the blue and yellow LEDs come on. After they are lit release the
setup button. The blue and yellow LEDs flash (setting mode for holding brake).
• You can activate and deactivate or select the effect of the holding brake by briefly pressing the setup
button. The flash rhythms of the blue and yellow LED change.
Flash # 1x 2x 3x
Holding brake Off 5% 10%
• Hold down the setup button for at least 2 seconds, this saves the setting and the programme mode is
exited.
• If the setup button is not pressed for some 10 seconds, the programming mode is automatically exited
without saving the changes to the settings.
Dead Band Setting
The so-called "Dead-Band" setting allows you to adjust the transmission period between forward
propulsion and braking. A low value means that the transmission period is very small, which requires a
particularly finely graded transmitter signal (e.g. as with high quality transmitters). A high value should be
used for simple transmitters.
• Press and hold the setup button; until the blue and red LEDs come on. After they are lit release the setup
button. The blue and red LEDs flash (setting mode for "Dead Band").
• You can change the settings by briefly pressing the setup button. The flash rhythm of both LEDs changes.
Flash # 1x 2x 3x
Dead Band 2% 3% 4%
• Hold down the setup button for at least 2 seconds, this saves the setting and the programme mode is
exited.
• If the setup button is not pressed for some 10 seconds, the programming mode is automatically exited
without saving the changes to the settings.
2x
LiPo with 2 cells (7.4V)
2x
Reverse mode turned on
3x 4x 5x 6x 7x 8x
30% 40% 45% 50% 55% 60%
4x 5x 6x 7x 8x 9x
15% 20% 25% 30% 35% 40%
4x 5x
5% 6%
Select Driver Profile
The control unit has 5 preprogrammed driver profiles, which differ in their predefined settings. Driver profile
5 also restores the factory settings whereby the low voltage protection is switched off (rechargeable battery
type is retained).
For this reason, driver profile 5 can be used to drive without low voltage protection.
However, we do not recommend such use, as the rechargeable battery can be damaged
in the case of low voltage (e.g. when using LiPo rechargeable batteries <3.0V)!
• Press and hold the setup button; until all four LEDs come on. After they are lit release the setup button.
The four LEDs flash (setting mode for driver profile).
• You can change the setting by briefly pressing the setup button. The flash rhythm of all four LEDs
changes.
Flash #
Driver profile
Cut Off
Reverse mode
Reverse mode proportion
Max. brake performance
Holding brake
Dead Band
• Hold down the setup button for at least 2 seconds, this saves the setting and the programme mode is
exited.
• If the setup button is not pressed for some 10 seconds, the programming mode is automatically exited
without saving the changes to the settings.

Brake Function & Reverse Mode
When changing between forwards and reverse (if activated) the speed lever must be put briefly into the
neutral position (ca. 2 seconds).
If the speed lever is shifted directly from forwards to reverse, the control unit's brake will be activated (the
vehicle will NOT go backwards!) The brake performance can be programmed as described above.

Ending Operation
• First switch off the control unit (bring switch into the "OFF" position).
• Separate the rechargeable battery from the control unit.
• Only now should you turn off the transmitter.

Disposal

Electric and electronic products do not belong in the household waste!
When the product is no longer usable, dispose of it in accordance with the applicable
9x 10x
statutory regulations.
65% 70%

Technical Data
Type:
Order No.:
Brushless motor:
Steady current forwards 5 min:
Steady current forwards 30 sec:
Idle speed (at 7.2V):
Control unit:
Number of cells NiCd/NiMH:
10x
Number of cells LiPo:
45%
BEC:
Steady current forwards 5 min:
Steady current forwards 30 sec:
Rechargeable battery connection:
Receiver connection:
Pulse frequency:
Functions:
These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1,
D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming,
or the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in
technology and equipment reserved.
© Copyright 2009 by Conrad Electronic SE.
1x 2x 3x
1 2 3
As selected As selected As selected
No Yes Yes
0% 50% 50%
30% 30% 40%
15% 10% 15%
3% 3% 4%
Hurricane 8T Hurricane 10T
235263 235264
60A 50A
80A 70A
34550 rpm 27710 rpm
6 6
2 2
Yes Yes
100A 100A
120A 120A
Tamiya-compatible
JR
16kHz
Proportional forwards, break, proportional reverse
4x 5x
4 5
As selected Off
No Yes
0% 25%
40% 30%
Off 10%
4% 3%
OFF
Hurricane 12T
235265
40A
60A
23310 rpm
6
2
Yes
100A
120A