Inhaltsverzeichnis
Werbung
PART 6 • Quick Set Up Guide • English
LNB: Select "LNB" and press OK. In the "LNB field", select one of the available LNB's. If you want to set
n
LNB related values, press OK and the LNB Set-up menu will be displayed. Refer to "LNB Set-up" below.
Dish Position: Select "Dish position" and press OK button. It displays the dish position of the current
n
satellite. When you use a DiSEqC 1.2 positioner, you can select dish position in this field. To set a dish
position, the status must be "ON" (in case the position has already been set) or "Off" (in case the position has
not been set).
Note: If in the "LNB Set-up" menu described below, the "LNB Dish" item is set to "fixed" you will not be able
to change the dish position settings in the channel set up menu. Only when you have selected the "LNB
Dish" to "moved", you will be able to change the settings in the channel set up menu.
2. Press OK button to set dish position. The "Positioner Set-up" menu will be displayed.
Frequency, Polarization, Symbol Rate: Shows the transponder (TP) values of the current satellite. To
n
change the value, select "Frequency" and press OK. The list of TP values of the current satellite is displayed.
Scan Mode: Designate channels scanning whether "FTA" (Free to Air) only or "All" channels (including
n
scrambled channels)
Press Auto Scan (Red Button) to search all the transponders of the selected satellite.
n
After the scanning is finished, press the Exit button to go to view mode.
n
Tip: Check the level and quality of the signal bar before searching any channels. The signal level of the TP of the
current satellite is displayed. The green bar is displayed if the settings are correct, otherwise the red bar
is displayed and you cannot get the channel. In the latter case, check if your dish is aimed at the selected
satellite or if the DiSEqC switch of the LNB overlaps with another satellite. Also, change the Frequency until
the Green bar is displayed to get the valid transponder. To switch between the TV/Radio channels list, you
will have to press the TV or Radio buttons on your remote accordingly.
3.3 LNB Set-up
To set up your LNB, please apply the following steps:
1. Press the Menu button, select "Installation", select "LNB Set-up" and press OK.
LNB: Up to 16 LNBs are available, select the correct one according to your LNB specifications. The
n
Default is set to Universal mode (9750/10600MHz).
LNB Type: Select the LNB type from Universal 1 ~ 3, and Single. You should type the LNB value in Single.
n
In Single, the item parameter is 0 or another number. In UNI1=9750/10600 MHz, UNI2=9750/10700MHz,
UNI3=9750/10750 MHz
LNB Dish: Using the Left/Right buttons, select "Fixed" or "Motorised" (Move) Dish. If you use a motorised
n
dish, read the "Positioner Set-up" instructions below.
DiSEqC switch: The default is Off. To use the DiSEqC switch, set up the DiSEqC version you have (V1.0 or V1.1).
n
DiSEqC Input: Select position 1~4 if DiSEqC switch is DiSEqC V1.0. Select position 1~16 if DiSEqC
n
switch is DiSEqC V1.1.
3.4 Positioner Set-up (if you are using a Motorised positioner with DiSEqC1.2)
If you are using a motorised positioner with DiSEqC 1.2 you will have to set the positions of the satellites you want to
scan. This function is available only if in the "LNB Set-up" menu and the LNB Dish field is set to "Moved". As described
in "LNB Set-up" above.
1. Select the "Dish Position" field in the "Channel Set-up" menu and press the OK.
2. Go to field "Centre" and use your Left/Right buttons to put the centre field to "ON".
3. Press OK, and your dish will move to the centre position. It takes your dish maximum 30 seconds to move to
its central position.
To set the position of your selected satellite:
1. Go to the "Movement field" and move your dish towards the correct direction, and keep this direction button
pushed in continuously. Once the receiver has found the correct position for the selected satellite, the word
"Locked" will appear above the signal level and quality indicator.
www.strongsat.com
Werbung
Inhaltsverzeichnis
