Chamberlain MotorLift500 Anleitungen Seite 12

Start by Reading These Important Safety Rules
These safety alert symbols mean WARNING – a personal safety or property damage instruction.
Read these instructions carefully.
This garage door opener is designed and tested to offer reasonable safe service provided it is installed and operated in
strict accordance with the following safety rules.
Failure to comply with the following instructions may result in serious personal injury or property damage.
WARNING: If your garage has no service entrance door, Model 1702EML Outside Quick Release must be installed. This accessory allows
manual operation of the garage door from outside in case of power failure.
Keep garage door balanced. Sticking or binding doors must
be repaired. Garage doors, door springs, cables, pulleys,
brackets and their hardware are under extreme tension and
can cause serious personal injury. Do not attempt to loosen,
move or adjust them. Call for garage door service.
Do not wear rings, watches or loose clothing while
installing or servicing a garage door opener.
To avoid serious personal injury from entanglement, remove
all ropes connected to the garage door before installing the
door opener.
Installation and wiring must be in compliance with your local
building and electrical codes. This is a class 2 double
insulated product, connection to earth is not required or
provided.
Lightweight doors of fiberglass, aluminum or steel must
be substantially reinforced to avoid door damage. The
best solution is to check with your garage door manufacturer
for an opener installation reinforcement kit.
The safety reverse system test is very important. Your
garage door MUST reverse on contact with a 40mm obstacle
placed on the floor. Failure to properly adjust the opener may
result in serious personal injury from a closing garage door.
Repeat the test once a month and make any needed
adjustments.
This unit should not be installed in a damp or wet space.
Door must not extend over a public byway during
operation.
Table of Contents
Safety Rules
Before You Begin
Door Types
Tools Required
Hardware Provided
Completed Installation
Assembly
Installation
Adjustment
Test the Safety Reverse System
Install The Protector System™
(Optional)
Program Remote
Replace Light Bulb
Operation Of Your Opener
Care Of Your Opener
Maintenance Of Your Opener
Having a Problem?
Wiring the Multi-Function Door
Control Panel and the Lighted
Door Control Button (Optional)
Accessories
Replacement Parts
Specifications
Before You Begin
1. Look at the wall or ceiling above the garage door. The header bracket
MUST be securely fastened to structural supports.
2. Do you have a finished ceiling in your garage? If so, a support bracket
and additional fastening hardware (not supplied) may be required.
3. Do you have an access door in addition to the garage door? If not,
Model 1702EML Outside Quick Release Accessory is required.
Page Illustration(s)
1
1
1 1
1 2
1 3
1 4
2 5 - 10
2 - 3 11 - 16
3 17 - 18
3 19
3
3 20
4 21
4
4
4
4
5 22
5 23
5 24
5
Fasten the child warning label adjacent to the lighted door
control button as a reminder of safe operating procedures.
Disengage all existing garage door locks to avoid damage
to garage door.
Any door control buttons (if installed) MUST be located
where the garage door is visible, but out of the reach of
children. Do not allow children to operate push button(s)
or remote control(s). Serious personal injury from a
closing garage door may result from misuse of the
opener.
Activate opener ONLY when the door is in full view, free
of obstructions and opener is properly adjusted. No one
should enter or leave the garage while the door is in
motion. Do not allow children to play near the door.
Use manual release only to disengage the trolley and, if
possible, ONLY when the door is closed. Do not use the red
handle to pull the door open or closed.
Disconnect electric power to the garage door opener
before making repairs or removing covers.
This product is provided with a transformer and power supply
cord of special design which, if damaged, MUST be
replaced by a transformer from your local Chamberlain
distributor and fitted by a specialist.
SAVE THESE INSTRUCTIONS
1
Door Types
A. One-Piece Door with Horizontal Track Only
B. Sectional Door with Curved Track
NOTE: Unit will not work with One-Piece Doors with Horizontal and
Vertical Tracks, Double-Wing Doors, or Canopy Doors.
2
Tools Required for Installation
3
Hardware Provided
ASSEMBLY HARDWARE
1. Square Head Screw 6mm (2)
2. 8mm Carriage Bolt
3. Cable Pulley
4. Pin
INSTALLATION HARDWARE
7. 6mm Nut
8. Concrete Anchor
9. 6mm Lag Bolt
10. 6mm Self-Threading Screw (4)
11. 6mm Hex Bolt
12. Wire Clips
4
Completed Installation
As you proceed with the assembly, installation and adjustment
procedures in this manual, you may find it helpful to refer back to
this illustration of a completed installation.
(1) Cable Pulley Bracket
(2) Trolley
(3) Chain/Cable Assembly
(4) Rail
(5) Hanging Bracket
(6) Power Cord
(7) Opener
5. 8mm Lock Nut
(1) 6. Pulley Bracket
(1)
(1)
13. Hex Screws
(6)
14. C-Rail Bracket
(4)
15. Clevis Pin
(4)
16. Ring Fastener
17. Flat Washer
(4)
(3)
(8) Light Lens
(9) Manual Release
Rope & Handle
(10) Door Arm
(11) Door Bracket
(12) Header Bracket
(1)
(1)
(2)
(1)
(2)
(2)
(1)