Operating Procedures - Hitachi CS25EC Bedienungsanleitung

4. Operating procedures

Fuel (Fig. 2-1)
WARNING!
The chain saw is equipped with a two-
stroke engine. Always run the engine on
fuel, which is mixed with oil.
Provide good ventilation, when fueling or
handling fuel.
Fuel
Always use branded 89 octane unleaded
gasoline.
Use genuine two-cycle oil or use a mix
between 25:1 to 50:1, please consult the oil
bottle for the ratio or HITACHI dealer.
If genuine oil is not available, use an anti-
oxidant added quality oil expressly labeled
for air-cooled 2-cycle engine use(JASO FC
GRADE OIL or ISO EGC GRADE). Do not
use BIA or TCW (2-stroke water-cooling
type) mixed oil.
Never use multi-grade oil (10 W130) or
waste oil.
Always mix fuel and oil in a separate clean
container.
Always start by filling half the amount of fuel,
which is to be used. Then add the whole
amount of oil. Mix (shake) the fuel mixture.
Add the remaining amount of fuel.
Mix (shake) the fuel-mix thoroughly before
filling the fuel tank.
Fueling
WARNING! (Fig.2-2)
Always shut off the engine before refuel-
ing.
Slowly open the fuel tank (1), when filling
up with fuel, so that possible over-
pressure disappears.
Tighten the fuel cap carefully, after fuel-
ing.
Always move the unit at least 3 m (10 ft.)
from the fueling area before starting.
Fig. 2-1
Fig. 2-3
Before fueling, clean the tank cap area care-
fully, to ensure that no dirt falls into the tank.
Make sure that the fuel is well mixed by
shaking the container, before fueling.
Chain oil (Fig. 2-2)
Fill up with chain oil (2). Always use good
quality chain oil. When the engine is running,
the chain oil is automatically discharged.
NOTE!
When pouring fuel (1) or chain oil (2) into the
tank, place the unit with cap side up.
(Fig. 2-2)
ADJUSTMENT OF CHAIN OIL SUPPLY
The chain oil quantity discharged through the
lubrication system is factory adjusted to the
maximum. Adjust the quantity in accordance
with the operating condition.
Turn the adjusting screw (1) counterclockwise
to increase the quantity and turn it clockwise to
decrease the quantity. (Fig. 2-2B)
(standard setting turns counterclockwise 1–1
1/2 from slightly seated)
Starting (Fig. 2-3, 4)
WARNING!
When the engine starts with the throttle
lock engaged, the engine speed is high
enough to make the chain rotate.
Fig. 2-2
Fig. 2-4
CAUTION!
Before starting, make sure chain brake is
disengaged (if so equipped) and that the
bar/chain does not touch anything.
1. Set ignition switch (1) to ON position.
* Push priming bulb (5) several times so
that fuel flows through bulb into carburetor.
(If so equipped)(Fig. 2-4)
2. Pull choke knob fully to choked position.
This will automatically lock the throttle in
starting position. (Fig. 2-4)
3. Pull recoil starter briskly, taking care to keep
the handle in your grasp and not allowing it
to snap back. (Fig.2-4)
4. When you hear the engine want to start,
with the safety trigger (2) pressed pull
throttle trigger (4). This will release the
throttle from starting position to run position
and will return the choke knob to run
position automatically. (Fig. 2-3, 4)
5. Pull recoil starter briskly again in the
aforementioned manner.
NOTE!
If engine does not start, repeat procedures
from 2 to 5.
6. After starting engine, pull throttle trigger to
release throttle lock. Then allow the engine
about 2-3 minutes to warm up before
subjecting it to any load.
Starting warm engine
1. Set ignition switch ON position.
Pull recoil starter.
2. If engine does not start easily, pull choke
knob fully and return it. This will lock the
throttle lever in starting position.
Pull recoil starter.
NOTE!
If engine still does not start, follow the steps of
the cold engine starting.
G
B
Fig. 2-2B
GB-7