Safety Instructions - Conrad Electronic 75 16 48 Bedienungsanleitung

O P E R A T I N G I N S T R U C T I O N S
8.5 mm CCD colour camera
420 TVL 6 mm
Item-No. 75 16 48
Intended use
This 8.5 mm (1/3") colour camera with 24 IR LEDs is intended for the visual surveil-
lance and protection of critical or obscured areas (e.g. foyers, parking lot surveillance).
The camera is suitable for operation in outdoor areas (IP65). The voltage is supplied
via 12 V/DC (suitable power supply is available as an option).
The integrated IR LEDs enable a range of up to max. 20 metres.
The integrated infrared LEDs allow night vision. Please note that with increasing dark-
ness and the associated activation of the IR LEDs, the coloured image reproduction
changes into black and white monochrome. The brightness is detected by the camera
using a photo sensor on the front.
Please bear in mind that it is prohibited by law to observe strangers with this camera
without their knowledge and consent.
Operating the product in any other way than described above is not permitted and may
lead to damage to the product, which can give rise to risks such as short circuit, fire and
electric shock. The product must not be modified or converted. Always observe the
safety instructions included in these operating instructions. Read the operating
instructions carefully and keep them for later reference.
Scope of delivery
• Camera
• Mounting bracket
• Installation material
• Operating Instructions
Explanation of symbols
A lightning symbol in a triangle indicates a health hazard, e.g. danger
D
of an electric shock.
The exclamation mark in a triangle indicates a particular risk during
handling, operation and control.
The „Hand" symbol indicates special tips and operating information.

Safety instructions

The warranty will be void in the event of damage caused by failure to
observe these safety instructions! We do not assume any liability for
consequential damage!
We do not assume any liability for damage to property or personal
injury caused by improper handling or non-compliance with the safety
instructions! The warranty will be void in such cases.
• The camera must not be modified or converted, as not only the CE
approval will become void but also the warranty.
• The integrated infrared LEDs allow night vision. Please note that with
increasing darkness and the associated activation of the IR LEDs, the
coloured image reproduction changes into black and white mono-
chrome. The brightness is detected by the camera using a photo
sensor on the front.
• The camera should not be exposed to extreme temperatures, direct
sunlight, intense vibrations or heavy mechanical stress.
• If the device is used with other devices e.g. a monitor, the operating
instructions and safety notices of the connected devices must be
followed.
• The use of the surveillance camera system does not replace the per-
sonal supervision of children, or people who require special
assistance, but only serves as a support to this supervision.
• After rapid changes in temperature, the camera requires sufficient
time to stabilise, in order to adjust to the surrounding temperature,
before it can be used.
• Electronic devices are not toys and should be kept out of the reach
of children!
• If you have doubts concerning the proper use of the system-
components or the safety, please refer to a qualified specialist.
• Never leave the packaging material lying around unattended. Plastic
film/bags etc. can be dangerous playthings for children, there is a
risk of suffocation.
www.conrad.com
Version 08/09
• If you have reason to assume that safe operation is no longer
possible, disconnect the device immediately and secure it against
inadvertent operation.
• You can assume that a safe operation is no longer possible if:
- the device is visibly damaged,
- the device does not function any longer and
- if the device has been stored under unfavourable conditions for a
long period of time
or
- it has been subjected to considerable stress during transportation.
• In commercial installations, the accident preventionregulations of
the Employer's Liability Insurance Association for electrical systems
and operating materials are to be observed.
• The camera is suitable for operation in outdoor areas (IP65).
• The voltage is supplied via 12 V/DC (suitable power supply is
available as an option).
• Make sure that all the electric connections and connection cables
between the devices and any extensioncables conform to the
regulations and comply with the operatinginstructions.
• Live components may be exposed, if the covers are opened or parts
removed (unless this can be done without tools). Connection points
may also be live. If the appliance needs to be opened for calibration,
servicing, repair or to replace parts or circuit boards, it must be first
disconnected from all sources of current. If servicing or internal
repairs are necessary, this must be carried out by a specialist who is
familiar with the risks involved and with the relevant regulations.
• Capacitors in the device may still be charged, even if the device has
been disconnected from all power supplies.
• When installing/mounting the appliance, make sure that the
connection cable is neither pinched nor damaged by sharp edges.
• Disconnect the camera from the power supply if the camera will not
be used for a long period of time.
• Disconnect the camera from the power supply before cleaning.
• For safety reasons, disconnect the camera from the power supply
during thunderstorms.
• Never replace damaged mains cables yourself. In such an event, dis-
connect the appliance from the mains and take it to a specialist work-
shop.
• Never pour fluids out above electrical devices. You run the risk of
causing a fire or a fatal electric shock. If liquids enter the device,
immediately disconnect it from the power supply, remove the plug
from the mains and consult an expert.
• Maintenance, adjustment and repairr works may only be performed
by a specialist or a qualified workshop.
• For any unanswered questions please contact our customer service
or other specialists.