•
Lær din maskine at kende. Gør dig bekendt med
dens anvendelse og dens begrænsninger, men også
med de specifikke potentielle farer.
•
Kontroller at kontakten står på AUS inden stikket
sættes i strømkontakten.
•
Sørg for at maskinen er ordentlig rengjort og smurt.
•
Inden ibrugtagning skal du kontrollere maskinen for
beskadigede dele og afgøre, om delene fungerer
korrekt og opfylder deres funktion. I tvivlstilfælde
skal delen udskiftes.
•
Kontroller alle bevægelige deles justering, alle knæk-
kede eller fastgørelsesanordninger og alt andet, der
kan påvirke den korrekte funktion. Alle beskadigede
dele skal straks repareres eller udskiftes af en fag-
mand.
•
Brug ikke maskinen, hvis en kontakt ikke kan tændes
eller slukkes korrekt.
Bemærk! Inden arbejdet påbegyndes undersøges ar-
bejdsområdet for skjulte elektriske ledninger, gas- og
vandrør.
Drift
Brug kun maskinen uden fejl.
•
Tving ikke maskinen eller tilbehøret til at udføre ar-
bejde som en større industriel maskine. Den yder
et bedre stykke arbejde med den kapacitet, den er
beregnet til.
•
Foretag alle justeringer på slukket maskine.
•
Lad ikke maskinen være uden opsyn, mens den
kører.
•
Når maskinen slukkes, må du først forlade den, når
den er stoppet helt.
•
Sluk altid for maskinen inden stikket tages ud.
•
Tag altid stikket ud af stikkontakten. Træk ikke stikket
ud ved at trække i ledningen.
•
Vedligehold og rengør maskinen regelmæssigt.
•
Lad maskinen kontrollere, hvis det er nødvendigt.
Hvis du er usikker på om nogle arbejdsbetingelser
er sikre eller ej, så lad være med at arbejde med
maskinen.
UDSTYR FIG. 1
1. Håndtag
2. Tænd/sluk kontakt
3. Ekstra håndtag
4. Chuck låsning
5. Værktøjsholder
6. Oliepåfyldning
7. Unbraconøglen
•
Get to know your machine. Familiarise yourself with
its application and limitations, as well as the specific
potential hazards.
•
Make sure that the switch is OFF before inserting the
plug into the socket.
•
Make sure that the machine is assembled completely
and properly.
•
Check the machine before use for damaged parts
and determine whether these parts work properly
and perform its intended function; in case of doubt,
the part is to be replaced.
•
Check the alignment of all moving parts, broken or
mounting parts, and other conditions that could im-
pair proper operation. Any damaged part should be
repaired or replaced by a qualified technician.
•
Do not use the machine if a switch cannot be
switched on and off correctly.
Caution! Before beginning the operation, check the in-
stallation site for concealed electrical cables, gas and
water pipes using a pipe locator.
Operation
Use only proper equipment.
•
Do not force the machine or accessory not to do the
work of a larger industrial machine. It works better at
the power rating for which it was designed.
•
Make all machine adjustments only with the machine
switched off.
•
Never leave the machine unattended while it is run-
ning.
•
When switching off, leave the machine only after it
comes to a complete standstill.
•
Turn the machine off before you unplug it.
•
Always unplug the mains cord. Never pull out the
plug from the wall outlet by holding the cable.
•
Perform maintenance and cleaning of the device
regularly.
•
Have the device checked, if necessary.
If you are not sure whether a working condition is
safe or unsafe, do not work with the machine.
FEATURES FIG.1
1. Handle
2. On / Off switch
3. Additional handle
4. Bohrfutter-Verriebelung
5. Tool holder
6. Oil fill opening
7. Allen key
17