Setting Up And Connecting The Unit; Replaying Music Pieces - IMG STAGE LINE CD-292USB Bedienungsanleitung

GB 4 Setting up and
Connecting the Unit
The control unit and the player mechanism unit
are designed for installation into a rack for units
with a width of 482 mm / 19", however, they can
also be used as tabletop units. In any case, the
player mechanism unit must be operated in a
horizontal position while it is possible to install
the control unit as desired, e. g. also in an
inclined position. For rack installation, 2 rack
spaces each are required for the control unit and
for the player mechanism unit (1 rack space =
44.45 mm).
Prior to making or changing any connections,
switch off the CD / MP3 player and the units to be
connected.
1) Connect the control unit and the player mech-
anism unit via the two connection cables sup-
plied:
Jack CONNECT TO REMOTE CONTROL 2
(35) of the player mechanism unit to the jack
REMOTE CONTROL CONNECT TO MAIN
UNIT 2 on the control unit
Jack CONNECT TO REMOTE CONTROL 1
(37) of the player mechanism unit to the jack
REMOTE CONTROL CONNECT TO MAIN
UNIT 1 on the control unit.
2) Connect the two signal outputs LINE OUT
(32, 39) to one input each with line level e. g.
of a mixer or amplifier (possible lettering:
Line, CD, Aux).
3) The two player units can be started and set to
pause via a mixer with fader start function.
For this purpose, connect the jacks START /
PAUSE (33, 38) via two cables with 3.5 mm
plugs to the corresponding jacks of the mixer.
Set the CD-292USB to the type of fader start
of the mixer, see chapter 6.
4) Finally connect the plug of the mains cable
(36) to a mains socket (230 V~ / 50 Hz).
5 Operation
The operation of the two player units is identical.
Switch on the unit with the POWER switch (28).
The display (10) shortly shows "boot" (starting
procedure) and WELCOME. If a CD has been
inserted, after reading-in, the display shows
information about the CD. If there is no CD in the
player mechanism, "no diSC" (no CD) is dis-
played,
Switch off the unit after operation. The fol-
lowing adjustments remain stored for the next
operation:
1. the operating mode selected (single title
replay / continuous replay,
2. the time indication selected (remaining play-
ing time / time already played,
3. the speed adjusting range selected
( chapter 5.9)

5.1 Replaying music pieces

1) To insert a CD, open the CD tray (25, 31) with
the button (4, 27 or 29). Insert the CD with
the lettering facing upwards and close CD
tray with the button .
2) Additionally or alternatively, a USB stick each
can be inserted into the USB ports (26, 30) or
a hard disk each can be connected to the
USB ports. To switch over between CD and
USB storage medium, press the button CD /
USB (5). For this purpose, the player unit
must be set to pause; if required, press the
button (20).
12
If two USB storage media are connected,
after pressing the button CD / USB, select the
signal source (CD, USB 1, USB 2) with the
button
the selection. The signal source currently
selected is skipped. Confirm the selection
with the button CD / USB.
Notes
1. The selected signal source is also indicated in
the display field (K):
"CD" = CD player mechanism is selected
"USB" constantly inserted = USB 1
"USB" flashes = USB 2
2. A hard disk must be supplied with power by a
power supply unit of its own if its power con-
sumption is higher than 500 mA.
3. If several partitions are provided on a hard disk,
these can be selected as follows:
a) Keep the button FOLDER (12) pressed until
b) With the button
c) To confirm, press the button FOLDER.
3) To start the first title, press the button
While replaying, the display shows the sym-
bol
continued at any time with the button
4) To select another title, use the buttons
.
Button
Button
currently playing. Each time the button is
pressed, the unit always goes back one more
title.
If one of the buttons is kept pressed, the titles
can quickly be selected with the jog wheel
(16).
5) For MP3 operation: If the music titles are
sorted in different folders, press the button
FOLDER (12) to select a folder. The display
shows "FO-SEL" (Folder Selection) and the
text line (O) shows the name of the folder.
The digits (A) on the top left of the display
now show the number of the folder and the
digits (N) under "Total" show the quantity of
the folders available.
Select the folder with the button
one of the buttons is kept pressed, the folders
can quickly be selected with the jog wheel
(16).
To confirm the selection, press the button
FOLDER; the display shows the playing time
(P) again. Select the desired title in the folder
with the button
6) To insert another CD, first set the unit to
pause with the button
chapter 5.4.1)
tray cannot be opened with the button .
7) Prior to switching off the unit, always close
chapter 5.3) the CD trays with the buttons
laser systems against impurities. Afterwards
switch off the unit with the POWER switch.
5.2 Loading the play list
To play a certain selection of MP3 files, it is pos-
sible to load play lists with the file extension
"wpl", "xml" or "m3u" created on a computer into
the CD-292USB.
Important: The play list and the corresponding
MP3 files must be on the same storage medium.
The play lists must always be stored in the root
directory.
1) If a title is played, set the unit to pause with
the button
2) Keep the button CONT / LIST (8) pressed and
select with the button
or (21). The text line (O) shows
the display shows "PA-SEL" (Partition Selec-
tion).
or select the partition.
The text line (O) shows the name in each
case.
(B). The replay can be interrupted and
: to go to the next title
: to go to the beginning of the title
or .
, otherwise the CD
to protect the
(20).
or (21) which file
extension is searched for. The text line (O)
shows the selection (M3U Scan, WPL Scan,
XML Scan).
3) Press the button FOLDER (12). The display
shows "FO-SEL" and the text line (O) shows
the name of the first play list. The digits (A) on
the top left of the display now show the num-
ber of the play list and the digits (N) under
"Total" show the quantity of the play lists
available.
4) Select the desired play list with the button
or .
5) To confirm the selection, press the button
FOLDER. After loading the list, the display
shows the playing time indication again (P).
6) To start the first title of the play list, press the
button . To select other titles from the list,
press the button
buttons pressed and actuate the jog wheel
(16).
7) To play the titles again without play list, set
the unit to pause with the button
button CONT / LIST pressed and press the
(20).
button or
appears in the text line. After releasing the
buttons, the display shows "SCAn" and then
.
again the playing time indication (P). Then no
more play list is loaded.
and
5.3 Indication of the title information
and the sleep mode
The display (10) indicates a variety of informa-
tion:
1. The number of the selected title (A) if
"TRACK" is shown above the digits. If
"FOLDER" is shown below the digits, the
number of the selected folder is indicated
[switchable with the button FOLDER (12)].
2. Quantity of the titles (N) on the CD or, if the
titles are sorted in different folders, the quan-
tity of the titles in the selected folder
3. Playing time of the selected title: relative (H)
and absolute (P); the seconds can be divided
into 75 so-called frames
The playing time indication can be switched
over with the button TIME (7):
or . If
If Elapse (E) is shown, the time already
played of the title is indicated.
If Total Remain (F, G) is shown, the remain-
ing time of the entire CD is indicated
(not possible for MP3 mode).
If Remain (G) is shown, the remaining time of
the title is indicated.
4. The text line (O) shows:
– the title name for standard audio CDs with
CD text
– the file name for MP3 mode
The text line can be switched over to the
indication of the following information (ID3
tags). For this purpose keep the button
TIME pressed and select with the button
or (21):
Indication (M)
TITLE
ALBUM
ARTIST
none = file name
5.3.1 Graphic indication of the playing time
In addition to the numerical time indication (P),
the bargraph (H) will indicate the playing time
graphically by its length, in relation to the dura-
tion of the title (relative time presentation). The
last 30 seconds of a title will be indicated by
the bargraph flashing in its full length, the last
15 sec onds by even faster flashing.
or or keep one of these
. Keep the
(21) repeatedly until "Folder"