Explanation Of The Symbols On The Equipment; Safety Information - Scheppach 5907107900 Originalbetriebsanleitung

Explanation of the symbols on the equipment

Introduction
MANUFACTURER:
scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
DEAR CUSTOMER,
we hope your new tool brings you much enjoyment and
success.
NOTE:
According to the applicable product liability laws, the
manufacturer of the device does not assume liability
for damages to the product or damages caused by the
product that occurs due to:
• Improper handling,
• Non-compliance of the operating instructions,
• Repairs by third parties, not by authorized service
technicians,
• Installation and replacement of non-original spare
parts,
• Application other than specified.
Unpacking
• Open the packaging and remove the device carefully.
• Remove the packaging material as well as the pack-
aging and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for transport
damage.
• If possible, store the packaging until the warranty pe-
riod has expired.
m ATTENTION!
The device and packaging materials are not toys!
Children must not be allowed to play with plastic
bags, film and small parts! There is a risk of swal-
lowing and suffocation!

Safety information

• Assemble the saw stand in the proper manner
before mounting the power tool. Proper assembly
is important to prevent the risk of a collapse of the
saw stand.
• Attach the power tool securely to the saw stand
before using it. Slipping off of the power tool on the
saw stand can lead to loss of control.
• Place the saw stand on a firm, level and horizon-
8 І 15
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
Read and follow the operating and safety instructions before you start working with this power tool.
tal surface. If the saw stand can slip off or wobbles,
the power tool or the workpiece cannot be uniformly
and securely guided.
• Do not overload the saw stand and do not use it
as a ladder or scaffolding. Overloading or standing
on the saw stand can lead to the upward shifting of
the centre of gravity of the stand and its tipping over.
• When working or transporting, take care that all
bolts and connecting elements are firmly tight-
ened. The attachment sets for the power tool must
always be firmly locked. Loose connections can lead
to instability and inexact sawing.
• Mount and dismount the power tool only when it
is in the transport position (for instructions on
the transport position, also see the operating in-
structions of the respective power tool). Other-
wise, the power tool can have such an unfavourable
centre of gravity that it cannot be held securely.
• When the power tool is mounted to the attach-
ment set, operate it exclusively on the saw stand.
Without the saw stand, the attachment set with the
power tool does not stand securely and can tip over.
• Ensure that long and heavy workpieces do not af-
fect the equilibrium of the saw stand. Long and/or
heavy workpieces must be supported at the free end.
• Keep your fingers clear of the hinge points while
pushing the saw stand together or pulling it
apart. Danger of fingers being crushed or contused.
Technical data
Dimensions (LxWxH) in
mm
Load in kg
Weight in kg
Cleaning and storage
Cleaning
• Keep the equipment free of dirt and dust as far as
possible. Wipe the equipment with a clean cloth or
blow it down with compressed air at low pressure.
• We recommend that you clean the equipment imme-
diately after you use it.
• Clean the equipment regularly with a damp cloth and
some soft soap. Do not use cleaningagents or sol-
vents; these may be aggressive to the plastic parts
in the equipment. Ensure that no water can get into
the interior of the equipment.
935-1945 x 545 x
805-915
150
9.8