Bosch PTS 10 Bedienungsanleitung Seite 32

OBJ_BUCH-783-007.book Page 32 Friday, June 27, 2014 9:29 AM
32 | English
Assembly
 Avoid unintentional starting of the machine. During as-
sembly and for all work on the machine, the power plug
must not be connected to the mains supply.
Delivery Scope
Please also observe the representation of the
delivery scope at the beginning of the operat-
ing instructions.
Before starting the operation of the machine for the first time,
check if all parts listed below have been supplied:
– Table saw
(Preassembled: Table width enlargement 10, saw blade
37, insert plate 3)
– Bottom plate 34 with pre-mounted cross-head screws
– Table extension 2
– Fastening kit for "table extension"39
(2 guide rods, 2 securing screws, 2 clips, 2 short fastening
knobs)
– Parallel fences 8 and 9
– Auxiliary stops 7 and 18
– Angle stop 16
– Fastening kit "for auxiliary stop/angle stop" 43
– Blade guard 5,
Riving knife 4 with pre-mounted hexagon bolt 35
– Vacuum hose 33
– Push stick 22
– Ring spanner 17
for machine versions with base unit:
– Base unit 67
(12 Profiles, 4 end caps)
– Fastening kit for base unit 66
(24 screws with nuts for assembly, 4 screws with nuts for
fastening of the machine, 4 washers)
Note: Check the power tool for possible damage.
Before further use of the machine, check that all protective
devices are fully functional. Any lightly damaged parts must
be carefully checked to ensure flawless operation of the tool.
All parts must be properly mounted and all conditions fulfilled
that ensure faultless operation.
Damaged protective devices and parts must be immediately
replaced by an authorised service centre.
Initial Operation
– Carefully remove all parts included in the delivery from
their packaging.
– Remove all packaging material from the machine and the
accessories provided.
– Take care that the packaging material under the motor
block es removed.
Additionally required tools (not in delivery scope):
– Cross-head screwdriver
– Angle gauge
– Box-end or open-end spanner (size 13 mm)
for assembly of the base unit
1 609 92A 0VS | (27.6.14)
Assembly Sequence
For easier working, observe the assembly sequence of the
supplied product features.
1. Assembly from Below
– Vacuum hose 33
– Bottom plate 34 with pre-mounted cross-head screws
2. Assembly from Above
– Riving knife 4
– Table extension 2
– Angle stop 16 and auxiliary stop 18
– Parallel guide 8 and auxiliary stop 7
Assembly from Below
– Turn the machine around so that it is upside down on the
saw table 11.
Mounting the Vacuum Hose (see figure a)
– Connect the chip ejector on the saw blade casing and the
chip ejector 31 on the machine housing with the vacuum
hose 33.
Mounting the Bottom Plate (see figure b)
– Insert the bottom plate 34 into the intended recesses so
that the cross-head screws can be screwed into the holes
of the housing.
– Fasten the bottom plate by screwing in and tightening the
cross-head screws.
Assembly from Above
– Turn the power tool around so that it is in the correct work-
ing position.
Mounting the Riving Knife (see figures c1–c3)
– Using the ring spanner 17, lift up the insert plate 3 at the
front and remove it from the notches 36.
– Turn the crank 12 counter-clockwise until it stops, so that
the saw blade 37 is positioned as high as possible over the
saw table.
– Loosen locking knob 29 to tilt the saw blade 37.
– Insert the riving knife 4 so that the respective holes are po-
sitioned on the guide bolts of the riving knife fixture 38.
– Fasten the riving knife 4 to fixture 38 by firmly tightening
hexagon bolt 35 with ring spanner 17 (13 mm).
– Readjust the saw blade back to 90° again and tighten lock-
ing knob 29. (also see "Adjusting Bevel Angles", page 34)
Note: The riving knife must be in alignment with the saw blade
to avoid jamming of the workpiece.
– Finally, reassemble the insert plate 3.
For this, hook the insert plate into the notches 36 and then
press the insert plate downward until it engages in the saw
table.
– Tighten the nut of the blade guard sufficiently with the ring
spanner 17 (13 mm) so that the blade guard remains se-
cured in any set position.
Mounting the Table Extension (see figures d1–d2)
For assembly, use the fastening kit for "table extension" 39.
(2 guide rods, 2 securing screws, 2 clips, 2 short fastening
knobs)
Bosch Power Tools