Candy FP 612 Bedienungsanleitung Seite 16

TO OPERATE THE ELECTRONIC CLOCK-PROGRAMMER
Preliminary Operations to Perform
After Plugging-in the Oven.
After initially plugging-in the unit, and after each interruption in
power, the lighted display on the control panel will respond by
flashing «AUTO»
Press the TIMER and END buttons along with the
buttons to set the exact time.
When the
ready to be used manually.
Available Functions
— Manual operation
— Timed operation
— Semi-automatic operation (programmed end to the cooking time)
— Automatic operation (programmed beginning and end of cooking time)
Manual Operation (of the oven):
This has already been described in the section of PRELIMINARY OPERATIONS. Just press
the button to make the corresponding symbol appear in the center and remove the AUTO
indicator.
Using the Electronic Programmer
As described in the PRELIMINARY OPERATIONS section, the electronic programmer allows the
oven to be operated manually or by:
— The timer;
— Programming the end of the cooking time (semi-automatic operation);
— Programming the beginning and end of the cooking time (automatic operation).
Using the Timer
While pressing the button, use the
maximum). Setting the desired time will light the
either as a manual function or automatic along with another program).
At the end of the set time the programmer sounds an interminent signal, to cancel the signal
press . While cooking, to display the time remaining press
Adjusting the Tone of the Timer Signal
Three different tones are available on the acoustic timer signal. To choose the bone desired,
press the button while the signal is sounding.
symbol appears on the display, the oven is
and buttons to select the desired time (23:59
symbol. (Note: This function can be used
.
28
Semi-Automatic Programming (end of cooking time)
Select oven temperature and cooking function.
To program only the shut-off (and not the turn-on) time of the oven proceed as follows.
Press the TIMER button along with either the
set the display to the desired cooking time. Release the buttons. The display responds by ligh-
ting the symbol and «AUTO», indicator.
The symbol on the display means the oven has begun to cook.
At the end of the cooking time, the oven shuts-off automatically, the programmer sounds a to-
or
ne, the symbol vanishes from the display, and the «AUTO» indicator begins to blink.
Remember that when the «AUTO» indicator is blinking, the
turn the oven to manual operation.
To display the cooking time remaining while cookingl press the TIMER button. Pressing the END
button shows the time when cooking will end
Automatic Programming (beginning and end of cooking time)
Select oven temperature and cooking function.
To program not only the oven shut-off time, but also the cooking time (and hence the turn-on ti-
me) the following steps must be performed:
1) Press and hold the TIMER button and use the
desired cooking time.
Upon releasing the buttons, the display will again show the current time, the «AUTO» indi-
cator, and the
2) Press and hold the END button and use the
time cooking is to finish.
When the buttons are released, the display will again show:
— The current time;
— The «AUTO» indicator.
Once the above steps are completed, the oven will automatically turn on and off at the desired
times.
The oven turn-on time will automatically be determined by the oven, based on the cooking times.
When the oven begins operation, the programmer will display with
indicator. When the oven shuts-off, the tone sounds and the
indicator begins to blink.
Remember that when the «AUTO» indicator is blinking, the
the oven to manual operation.
The tone signaling the end of the cooking time can be canceled by pressing the
To display the cooking time remaining while cooking, press the TIMER button. Pressing the END
button shows the time when cooking will end.
Warning: The symbols on the buttons may vary from model to model, but their functions
remain the same.
or button, and, while holding the buttons,
and
symbol.
and
29
bunon must be pressed to re-
buttons to set the display to the
buttons to set the display when
symbol and the «AUTO»
symbol disappears. The «AUTO»
button must be pressed to return
button.