Before Using The Equipment - EINHELL TE-RS 18 Li Originalbetriebsanleitung

L sound pressure level ..................... 74.3 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level ....................... 85.3 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 60745.
Vibration emission value a
K uncertainty = 1.5 m/s
The specifi ed vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equip-
ment is used and may exceed the specifi ed value
in exceptional circumstances.
The specifi ed vibration value can be used to
compare the equipment with other electric power
tools.
The specifi ed vibration value can be used for initi-
al assessment of a harmful eff ect.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Limit the operating time!
All stages of the operating cycle must be conside-
red (for example, times in which the electric tools
are switched off and times in which the tool is
switched on but operates without load).
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
Anl_TE_RS_18_Li_SPK1.indb 17 Anl_TE_RS_18_Li_SPK1.indb 17
= 5.33 m/s
2
h
2
- 17 -
GB
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.

5. Before using the equipment

Warning!
Always remove the battery pack before making
adjustments to the equipment.
Be sure to read the following information before
you put the cordless equipment into operation:
•
Charge the battery pack with the charger. An
empty battery pack requires a charging peri-
od of approximately 0.5 to 1 hour.
5.1 Installing the dust extractor adapter (Fig.
2/Item 2)
Plug the dust extractor adapter (2) onto the va-
cuum cleaner connector (a) as shown in Fig. 2.
Connect the dust extractor adapter to a suitable
dust extraction system.
5.2 Fitting the dust bag (Fig. 3/Item 4)
•
Fit the dust bag (4) on the dust extractor
adapter (2) by twisting it gently as far as the
notch (b) as shown in Fig. 3.
•
The dust is extracted directly into the dust
bag (4) through the abrasive paper and the
oscillating plate (5).
•
Twist and pull the dust bag simultaneously to
remove it again.
Caution!
For health reasons it is imperative that you use
the dust collection box or a dust extraction sys-
tem.
5.3 Fastening the abrasive paper with the Vel-
cro fastening system (Fig. 4)
•
Only use abrasive paper with the correspon-
ding dimensions and matching perforations.
•
Place the abrasive paper onto the oscillating
plate (4) as shown in Fig. 5. Make sure that
the perforations in the abrasive paper coinci-
de with the oscillating plate.
•
To remove the abrasive paper, simply pull it
off.
10.01.2017 15:04:11 10.01.2017 15:04:11