janitza UMG 509-PRO Installationsaleitung Seite 8

Janitza electronics GmbH Janitza electronics GmbH
Vor dem Polstück 6 Vor dem Polstück 6
D-35633 Lahnau / Germany D-35633 Lahnau / Germany
Support tel. +49 6441 9642-22 Support tel. +49 6441 9642-22
Fax +49 6441 9642-30 Fax +49 6441 9642-30
e-mail: info@janitza.com e-mail: info@janitza.com
www.janitza.com www.janitza.com
Safety
2
Safety
2
Safety information
Safety information
The installation manual does not represent a full
The installation manual does not represent a full
p-
listing of all necessary safety measures required m m Danger of life / damage to property Danger of life / damage to property
listing of all necessary safety measures required
.
due to disregard of the connection due to disregard of the connection
for safe operation of the device.
for safe operation of the device.
-
Certain operating conditions may require further conditions or impermissible conditions or impermissible
Certain operating conditions may require further
e
WARNING! WARNING!
overvoltage overvoltage
measures. The installation manual contains
measures. The installation manual contains
information that you must observe for your
information that you must observe for your
Your device can be damaged or destroyed by a failure to Your device can be damaged or destroyed by a failure to
own personal safety and to avoid damage to
own personal safety and to avoid damage to
comply with the connection conditions or by exceeding comply with the connection conditions or by exceeding
property.
property.
the permissible voltage range. the permissible voltage range.
Before connecting the device to the supply voltage, Before connecting the device to the supply voltage,
Symbols used:
e Symbols used:
check: check:
c This symbol is used as an addition
• The ground wire connection must be connected • The ground wire connection must be connected
c This symbol is used as an addition
to the safety instructions and
with the system earthing! with the system earthing!
L1 L1 to the safety instructions and
warns of an electrical hazard.
L2 L2
• Voltage and frequency correspond to the details on • Voltage and frequency correspond to the details on
warns of an electrical hazard.
L3 L3
the ratings plate! Limit values stipulated in the user the ratings plate! Limit values stipulated in the user This symbol is used as an addition
m
N N This symbol is used as an addition
m
manual have been complied with! manual have been complied with!
to the safety instructions and
to the safety instructions and
• In building installations, the supply voltage must be • In building installations, the supply voltage must be warns of a potential hazard.
warns of a potential hazard.
 protected with a UL/IEC approved circuit breaker / protected with a UL/IEC approved circuit breaker /
 This symbol with the word NOTE!
This symbol with the word NOTE!
a fuse! a fuse!
describes:
describes:
• The isolation device • The isolation device
• Procedures that do not entail
V V V V V V V V V V V V V V V V
2 4 ref 3 4 ref 3p 4wu 3p 4wu 1 2 1 3 • Procedures that do not entail 2 4 ref 3 4
- must be installed near the device and in a - must be installed near the device and in a
any danger of injury.
any danger of injury.
location that is easily accessible for the user. location that is easily accessible for the user.
• Important information,
• Important information,
- must be labelled to identify the respective device. - must be labelled to identify the respective device.
procedures or handling steps.
procedures or handling steps.
• Do not tap the supply voltage from the voltage • Do not tap the supply voltage from the voltage
transformer. transformer.
Safety instructions are highlighted with
Safety instructions are highlighted with
• Provide a fuse for the neutral conductor if the • Provide a fuse for the neutral conductor if the
a warning triangle and shown as follows,
a warning triangle and shown as follows,
L1 L1
neutral conductor terminal of the source is not neutral conductor terminal of the source is not
depending on the degree of hazard:
depending on the degree of hazard:
grounded. grounded.
L2 L2
Power Quality Analyser Power Quality Analyser
UMG 509-PRO UMG 509-PRO
Installation manual Installation manual
Residual current monitoring (RCM) Residual current monitoring (RCM)
Installation Installation
 
Device settings Device settings
 
m
m Indicates an immediately
Indicates an immediately
threatening hazard that leads to
threatening hazard that leads to
serious or even fatal injuries.
DANGER!
serious or even fatal injuries.
DANGER!
m
m
Indicates a potentially hazardous
Indicates a potentially hazardous
situation that could lead to
situation that could lead to
serious or even fatal injuries.
WARNING!
serious or even fatal injuries.
WARNING!
m
m
Indicates a potentially hazardous
Indicates a potentially hazardous
situation that could lead to minor
situation that could lead to minor
injuries or damage to property.
CAUTION!
injuries or damage to property.
CAUTION!
L1 L1
L2 L2
Measures for safety
L3 L3
Measures for safety
N N
When operating electrical devices certain parts
When operating electrical devices certain parts
of these devices inevitable carry dangerous
of these devices inevitable carry dangerous
voltages. This could result in serious bodily
voltages. This could result in serious bodily
injury or damage to property if not handled
injury or damage to property if not handled
properly:
properly:
S1 S2 S1 S2 S1 S2 S1 S2 S1 S2 S1 S2 S1 S2 S1 S2
• De-energise your device before starting I I I I I I I I
ref 3p 4w 1 3p 4w 2 3 1 2 4 3 4
• De-energise your device before starting
work! Check that it is de-energised.
work! Check that it is de-energised.
• Before establishing electrical connections
• Before establishing electrical connections
to the device, earth it at the ground wire
to the device, earth it at the ground wire
connection if there is one.
connection if there is one.
• Hazardous voltages may arise in all circuit
• Hazardous voltages may arise in all circuit
parts that are connected to the power supply.
parts that are connected to the power supply.
L1 L1
L2 L2
L3 L3
General General
1 1
Disclaimer Disclaimer
The observance of the information products The observance of the information products
for the devices is a prerequisite for safe opera- for the devices is a prerequisite for safe opera-
tion and to achieve the stipulated performance tion and to achieve the stipulated performance
characteristics and product characteristics. characteristics and product characteristics.
Janitza electronics GmbH accepts no liability Janitza electronics GmbH accepts no liability
for injuries to personnel, property damage for injuries to personnel, property damage
or fi nancial losses arising due to a failure to or fi nancial losses arising due to a failure to
comply with the information products. Ensure comply with the information products. Ensure
that your information products are accessible that your information products are accessible
and legible. and legible.
Further information can be found on our web- Further information can be found on our web-
site www.janitza.com at Support > Downloads. site www.janitza.com at Support > Downloads.
Copyright notice Copyright notice
User manual: User manual:
© 2017 - Janitza electronics GmbH - Lahnau. © 2017 - Janitza electronics GmbH - Lahnau.
All rights reserved. Duplication, editing, All rights reserved. Duplication, editing,
distribution and any form of exploitation, also distribution and any form of exploitation, also
as excerpts, is prohibited. as excerpts, is prohibited.
Subject to technical amendments Subject to technical amendments
• Make sure that your device agrees with the • Make sure that your device agrees with the
installation manual.
• Read and understand fi rst product-related • Read and understand fi rst product-related
documents.
Network systems Network systems
5 5
• Even after disconnecting the supply voltage,
• Even after disconnecting the supply voltage,
there may still be hazardous voltages present
Network systems and max. rated voltages (DIN EN 61010-1/A1): Network systems and max. rated voltages (DIN EN 61010-1/A1):
in the device (capacitor storage).
Three-phase, four-conductor
• Do not operate equipment with current
• Do not operate equipment with current
transformer circuits when open.
with earthed neutral conductor
• Do not exceed the limit values stipulated in
• Do not exceed the limit values stipulated in
the user manual and on the rating plate - even
during testing or commissioning.
• Observe the safety and warning information in
• Observe the safety and warning information in
the documents that belong to the devices!
Qualifi ed personnel
Qualifi ed personnel
In order to avoid injuries to personnel and
E E E E
In order to avoid injuries to personnel and
L1 L1
property damage, only qualifi ed personnel with
IEC U E E E property damage, only qualifi ed personnel with IEC U / U
L2 L2
L-N
electrical training are permitted to work on the
L3 L3
electrical training are permitted to work on the
UL U UL U / U
L-N
N N
devices with knowledge
devices with knowledge
Two-phase, two-conductor
• of the national regulations for accident
• of the national regulations for accident
prevention
• of safety standards
• of safety standards
• of installation, commissioning and operation
• of installation, commissioning and operation
S1 S2 S1 S2 S1 S2 S1 S2 S1 S2 S1 S2 S1 S2 S1 S2
I I I I I I I I of the device.
3p 2i 1 3p 2i 2 3 1 2 4 3 4
E E E
E E E
Only partially suitable for use Only partially suitable for use
L1 L1
in non-earthed networks
L2 L2
8 / 14
installation manual.
documents.
Proper use
The device is
there may still be hazardous voltages present
• intended for installation in switch cabinets
in the device (capacitor storage).
Three-phase, four-conductor Three-phase, four-conductor Three-phase, four-conductor Three-phase, three-conductor
system system system system
with earthed neutral conductor with non-earthed neutral conductor with non-earthed neutral conductor
transformer circuits when open.
L1 L1 L1 L1 L1 L1 L1 L1 L1 L1 L1 L1 L1 L1 L1
• not intended for installation in vehicles!
L2 L2 L2 L2 L2 L2 L2 L2 L2 L2 L2 L2 L2 L2 L2
L1 L1 L1 L1 L1 L1 L1 L1 L1 L1 L1 L1
the user manual and on the rating plate - even
L2 L2 L2 L2 L2 L2 L2 L2 L2 L2 L2 L2
during testing or commissioning.
N N N N N N N N N N N N N N N
N N N N
N N N N N N N N
the documents that belong to the devices!
R R R R R R R R • not intended for installation in environments
R R
L3 L3 L3 L3 L3 L3 L3 L3 R R R R L3 L3 L3 L3 L3 L3 L3
E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E
L3 L3 L3 L3 L3 L3 L3 L3 L3 L3 L3 L3
Only partially suitable for use in non-earthed networks Only partially suitable for use in non-earthed networks
E E E : 417 VLN / 720 VLL / U : 417 VLN / 720 VLL E E E E E E E E E E E E E E E E E E E E E
L-L L-N L-L
The prerequisites of faultless, safe operation
(see step 7). (see step 7).
: 347 VLN / 600 VLL / U : 347 VLN / 600 VLL
L-L L-N L-L
of this device are proper transport and proper
Two-phase, two-conductor Single-phase, two-conductor Single-phase, two-conductor Separated single-phase,
storage, set-up, installation, operation and
systems systems systems systems three-conductor systems
L1 L1 L1 L1 L1 L1 L1 L1 L L L L L L L maintenance. L
Non-earthed Non-earthed with earthed neutral conductor with earthed neutral conductor with earthed neutral conductor
prevention
L1 L1 L L
L1 L1 L1 L1 L L L L
of the device.
L2 L2 L2 L2 L2 L2 L2 L2 N N N N N N N N
E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E
L2 L2 L2 L2 L2 L2 N N N N N N
E E E E E E E E E E E E E E E E E E E E E E E E
IEC IEC U 480 VLN U 480 VLN IEC U
L-N L-N L-N
in non-earthed networks
UL UL U 480 VLN U 480 VLN UL U
(see step 7). (see step 7). L-N L-N L-N
• Keep product supporting documentation • Keep product supporting documentation
throughout the life available and, where ap- throughout the life available and, where ap-
propriate, to pass on to subsequent users. propriate, to pass on to subsequent users.
• Please inform yourself about device revisi- • Please inform yourself about device revisi-
ons and the associated adjustments to the ons and the associated adjustments to the
product-related documentation on product-related documentation on
www.janitza.com. www.janitza.com.
Disposal Disposal
Please observe national regulations! Please observe national regulations!
If disposing of individual parts, please dispose If disposing of individual parts, please dispose
of them in accordance with their nature and of them in accordance with their nature and
existing country-specifi c regulations, for existing country-specifi c regulations, for
example as: example as:
• Electrical scrap • Electrical scrap
• Plastics • Plastics
• Metals • Metals
Or, task a certifi ed disposal business with the Or, task a certifi ed disposal business with the
scrapping. scrapping.
Relevant laws, applied standards and Relevant laws, applied standards and
directives directives
The laws, standards and directives for the The laws, standards and directives for the
device applied by Janitza electronic GmbH device applied by Janitza electronic GmbH
can be found in the declaration of conformity can be found in the declaration of conformity
on our website. on our website.
Proper use
The device is
• intended for installation in switch cabinets
Three-phase, three-conductor Three-phase, three-conductor Three-phase, three-conductor
and small installation distributors (please
and small installation distributors (please
systems systems systems systems
observe step 3 "Assembly").
Non-earthed Non-earthed With earthed phase With earthed phase
observe step 3 "Assembly").
L1 L1 L1 L1 L1 L1 L1 L1 L1 L1 L1 L1 L1 L1 L1 L1 L1
• not intended for installation in vehicles!
L2
The use of the device in mobile equipment
L1 L1 L1 L1 L1 L1 L1 L1 L1 L1 L1 L1
The use of the device in mobile equipment
is considered to be non-standard
is considered to be non-standard
N
environmental conditions and is therefore
environmental conditions and is therefore
only permitted after separate agreement.
only permitted after separate agreement.
• not intended for installation in environments
L2 L2 L2 L2 L2 L2 L2 L2 L2 L2 L2 L2 L2 L2 L2 L2
with hazardous oils, acids, gases, vapours,
L3 with hazardous oils, acids, gases, vapours, L3 L3 L3 L3 L3 L3 L3 L3 L3 L3 L3 L3 L3 L3 L3 L3
L2 L2 L2 L2
L2 L2 L2 L2 L2 L2 L2 L2
dusts, radiation, etc.
E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E
dusts, radiation, etc.
L3 L3 L3 L3 L3 L3 L3 L3 L3 L3 L3 L3
U U
E E E E E E E E E E E E E E E E E E E E E
L-L L-L
600 VLL 600 VLL
The prerequisites of faultless, safe operation
of this device are proper transport and proper
Application areas for the Application areas for the
Separated single-phase,
storage, set-up, installation, operation and
three-conductor systems
device: device:
L1 L1 L1 L1 L1 L1 L1 L1
with earthed neutral conductor
maintenance.
• 2, 3 and 4 conductor • 2, 3 and 4 conductor
L1 L1
L1 L1 L1 L1
networks (TN and TT networks (TN and TT
networks). networks).
N N N N N N N N
• In residential and in- • In residential and in-
N N
N N N N
dustrial applications. dustrial applications.
L2 L2 L2 L2 L2 L2 L2 L2
E E E E E E E E E E E E E
L2 L2 L2 L2 L2 L2
E E E E E E E E E
IEC U / U : 400 VLN / 690 VLL / U : 400 VLN / 690 VLL
L-L L-N L-L
/ U UL U : 347 VLN / 600 VLL / U : 347 VLN / 600 VLL
L-L L-N L-L
2
3
6