Avdel Genesis Betriebsanleitung Seite 45

A c c e s s o r i e s
S w i v e l H e a d s
Instead of a nose assembly, a swivel head can be fitted to a base tool. It allows 360° rotation of the tool about the nose tip and
allows access into many applications otherwise too restrictive. There are two types of swivel heads: the straight swivel head with
the nose tip slightly offset from the centre line of the tool head and the right-angle swivel head with the nose tip on a perpendicular
axis to the head of the tool. See drawings below and page 14 for dimensions and page 15 for details.
PRIOR to fitting a swivel head, the base tool must be adapted. See Preparing the Base Tool page 14.
In contrast to nose assemblies part numbers of swivel heads do INCLUDE a nose tip as shown below.
Swivel heads can be ordered on their own or supplied with a base tool. See table below for part numbers. Jaws and nose tips vary
depending on the fastener to be placed but all other components remain the same within each type of swivel head. See the 'capability'
tables below and page 14 and the 'Constant Components ' table page 16.
'A' and 'B' dimensions will help you assess the accessibility of your application.
S T R A I G H T S W I V E L H E A D c a p a b i l i t y
F A S T E N E R
1
NAME Ø MATERIAL
AVEX ® 1 / 8 3.2
Al Alloy
1 / 8 3.2 Steel
5 / 32 4.0
Al Alloy
5 / 32 Steel
4.0
3 / 16 Al Alloy
4.8
® 5 / 32 Al Alloy
BULBEX 4.0
3 / 16 Al Alloy
4.8
® 1 / 8 Stainless Steel
AVINOX II 3.2
5 / 32 Stainless Steel
4.0
® – Al Alloy
AVSEAL II 4.0
–
4.0 Al Alloy
–
5.0 Al Alloy
–
5.0 Al Alloy
® 1 / 8
STAVEX 3.2 Steel
5 / 32
3.2 Steel
1 / 8
3.2 Stainless Steel
5 / 32 4.0 Stainless Steel
1
In inches then in millimetres.
I M P O R T A N T
S W I V E L H E A D
PART Nº
07 34 5-0 3 0 0 0
07 34 5-0 3 1 0 0
07 34 5-0 3 1 0 0
07 34 5-0 3 2 0 0
07 34 5-0 3 2 0 0
07 34 5-0 3 1 0 0
07 34 5-0 3 2 0 0
07 34 5-0 3 1 0 0
07 34 5-0 3 2 0 0
71 21 3-0 6 0 0 0
71 21 3-0 6 6 0 0
71 21 3-0 6 1 0 0
71 21 3-0 6 7 0 0
07 34 5-0 3 1 0 0
07 34 5-0 3 2 0 0
07 34 5-0 3 1 0 0
07 34 5-0 3 2 0 0
2
Long nose tip for deep placing.
Remove Male 'T' Adaptor 1 from the Tool (see page 10) and replace with
Jaw Spreader Housing (71210-02101).
N O S E T I P ( m m )
PART Nº 'A' 'B'
0 73 4 5- 03 60 0 7 .87 3 .81
0 73 4 5- 03 70 0 7 .87 3 .81
0 73 4 5- 03 70 0 7 .87 3 .81
0 73 4 5- 03 80 0 7 .87 3 .81
0 73 4 5- 03 80 0 7 .87 3 .81
0 73 4 5- 03 70 0 7 .87 3 .81
0 73 4 5- 03 80 0 7 .87 3 .81
0 73 4 5- 03 70 0 7 .87 3 .81
0 73 4 5- 03 80 0 7 .87 3 .81
7 12 1 3- 16 40 1 6 .35 1 .95
2
6 .35 4 .11
71 21 3 -1 64 02
7 .62 2 .00
7 1 21 3- 16 4 03
71 2 13 -1 64 0 4 2 7 .62 4 .11
0 7 34 5- 03 7 00 7 .87 3 .81
0 7 34 5- 03 8 00 7 .87 3 .81
0 7 34 5- 03 7 00 7 .87 3 .81
0 7 34 5- 03 8 00 7 .87 3 .81
COMPLETE TOOL PART NUMBER :
A
precede with 71401-30
(the stop nut and safety cap are included)
IMPORTANT: in contrast to complete tools
B
with nose assemblies, those fitted with swivel heads
include the nose tip as a part of the head.
see
J A W S
below
PART Nº
0 7 34 0 -00 2 13 ... 0 0 1
0 7 34 0 -00 2 13 ... 0 0 4
0 7 34 0 -00 2 13 ... 0 0 4
0 7 49 0 -04 6 02 ... 0 1 0
0 7 49 0 -04 6 02 ... 0 1 0
0 7 34 0 -00 2 13 ... 0 0 4
0 7 49 0 -04 6 02 ... 0 1 0
0 7 34 0 -00 2 13 ... 0 0 4
0 7 49 0 -04 6 02 ... 0 1 0
0 7 34 0 -00 2 13 ... 1 6 0
0 7 34 0 -00 2 13 ... 1 8 0
0 7 34 0 -00 2 13 ... 1 6 1
... 1 8 1
0 7 34 0 -00 2 13
... 0 0 4
0 7 34 0 -00 2 13
0 7 49 0 -04 6 02 ... 0 1 0
0 7 34 0 -00 2 13 ... 0 0 4
0 7 49 0 -04 6 02 ... 0 1 0
13