Inhaltsverzeichnis
Werbung
Connection diagram for standard mode
1. TEL terminal (TEL)
12.
15 cm
Note:
Refer to handsfree telephone
Depending on the kind of vehicle, the function
unit's manual (sold separately).
of 3* and 5* may be different. In this case, be
sure to connect 2* to 5* and 4* to 3*.
15 cm
2. Antenna jack
1*
3. This product
3*
2*
4. DSP switch
Switch the DSP switch
as illustration below.
5*
4*
13. Connect leads of the same
color to each other.
5. IP-BUS input (Blue)
14. Cap (1*)
When not using this terminal,
6. Multi-CD player
do not remove the cap.
(sold separately)
7. IP-BUS cable
17. Fuse holder
15. Yellow (3*)
16. Yellow (2*)
Back-up
To terminal always supplied
(or accessory)
with power regardless of
ignition switch position.
20. Fuse resistor
19. Red (4*)
18. Red (5*)
Accessory
To electric terminal controlled
(or back-up)
by ignition switch (12 V DC)
ON/OFF.
21. Orange/white
20. Fuse resistor
To lighting switch terminal.
22. Black (ground)
To vehicle (metal) body.
23. ISO connector
24. Yellow/black
Note:
If you use a cellular telephone, connect it via the
In some vehicles, the ISO connector may be
Audio Mute lead on the cellular telephone. If not,
divided into two. In this case, be sure to
keep the Audio Mute lead free of any connections.
connect to both connectors.
8. Jack for the Wired Remote Control (WIRED REMOTE INPUT)
Refer to Wired Remote Control's manual
26. Connecting cords with RCA pin
(sold separately).
plugs (sold separately)
9. Subwoofer output
(LOW/SUBWOOFER OUTPUT)
23 cm
10. Rear output
(MID/REAR OUTPUT)
15 cm
11. Front output
(HIGH/FRONT OUTPUT)
27. Power amp
(sold separately)
28. Blue/white
To system control terminal of the
power amp (max. 300 mA 12 V DC).
15 cm
29. System remote control
30. Blue/white (7*)
To Auto-antenna relay control terminal
(max. 300 mA 12 V DC).
31. Blue/white (6*)
32. The pin position of the ISO connector will differ
depends on the type of vehicle. Connect 6* and 7*
when Pin 5 is an antenna control type. In another
type of vehicle, never connect 6* and 7*.
33. Left
+
+
35. Front speaker
≠
≠
+
+
36. Rear speaker
≠
≠
+
+
25. Speaker leads
37. Subwoofer
≠
≠
White
: Front left +
White/black : Front left ≠
: Front right +
Gray
Gray/black : Front right ≠
38. Perform these connections when using
: Rear left +
the optional amplifier.
Green
Green/black : Rear left ≠
: Rear right +
Violet
Violet/black : Rear right ≠
Connection diagram for 3-way network mode
12.
Note:
27. Power amp
Depending on the kind of vehicle, the function
(sold separately)
of 3* and 5* may be different. In this case, be
sure to connect 2* to 5* and 4* to 3*.
27. Power amp
1*
(sold separately)
3*
2*
5*
4*
14. Cap (1*)
When not using this terminal,
do not remove the cap.
16. Yellow (2*)
15. Yellow (3*)
Back-up
To terminal always supplied
(or accessory)
with power regardless of
ignition switch position.
19. Red (4*)
18. Red (5*)
Accessory
To electric terminal controlled
(or back-up)
by ignition switch (12 V DC)
ON/OFF.
34. Right
35. Front speaker
21. Orange/white
To lighting switch terminal.
22. Black (ground)
To vehicle (metal) body.
36. Rear speaker
37. Subwoofer
23. ISO connector
Note:
In some vehicles, the ISO connector may be
divided into two. In this case, be sure to
connect to both connectors.
Fig. 10
Abb. 10
Afb. 10
8. Jack for the Wired Remote Control (WIRED REMOTE INPUT)
Refer to Wired Remote Control's manual
(sold separately).
1. TEL terminal (TEL)
39. Low range output
15 cm
Refer to handsfree telephone
(LOW/SUBWOOFER OUTPUT)
unit's manual (sold separately).
23 cm
15 cm
40. Middle range output
2. Antenna jack
3. This product
(MID/REAR OUTPUT)
15 cm
4. DSP switch
Switch the DSP switch
41. High range output
as illustration below.
(HIGH/FRONT OUTPUT)
13. Connect leads of the same
color to each other.
28. Blue/white
5. IP-BUS input (Blue)
To system control terminal of the
power amp (max. 300 mA 12 V DC).
15 cm
6. Multi-CD player
(sold separately)
7. IP-BUS cable
30. Blue/white (7*)
To Auto-antenna relay control terminal
(max. 300 mA 12 V DC).
17. Fuse holder
31. Blue/white (6*)
32. The pin position of the ISO connector will differ
depends on the type of vehicle. Connect 6* and 7*
when Pin 5 is an antenna control type. In another
type of vehicle, never connect 6* and 7*.
20. Fuse resistor
20. Fuse resistor
42. Speaker leads
24. Yellow/black
White
: High range left +
If you use a cellular telephone, connect it via the
White/black : High range left ≠
Audio Mute lead on the cellular telephone. If not,
: High range right +
Gray
keep the Audio Mute lead free of any connections.
Gray/black : High range right ≠
: Middle range left +
Green
Green/black : Middle range left ≠
Violet
: Middle range right +
Violet/black : Middle range right ≠
26. Connecting cords with RCA pin
plugs (sold separately)
27. Power amp
(sold separately)
27. Power amp
(sold separately)
27. Power amp
(sold separately)
29. System remote control
33. Left
34. Right
+
+
43. High range
43. High range
speaker
≠
≠
speaker
+
+
44. Middle range
44. Middle range
speaker
speaker
≠
≠
+
+
45. Low range
45. Low range
speaker
speaker
≠
≠
38. Perform these connections when using
the optional amplifier.
46. External amp is required for connecting the low
range speaker.
Fig. 11
Abb. 11
Afb. 11
Werbung
Inhaltsverzeichnis
