Connecting The Units - Pioneer DEH-P5100UB Installationsanleitung

2. Rear output
11. Note
1. This product
Depending on the kind of vehicle,
3. Front output
the function of 3* and 5* may be
different. In this case, be sure to
connect 2* to 5* and 4* to 3*.
4. Subwoofer output
1*
3* 2*
5. Antenna jack
7.Fuse (10 A)
5* 4*
12. Connect leads of the
same color to each other.
13. Cap (1*)
Do not remove cap
if this terminal is
not in use.
14. Yellow (3*) 15. Yellow (2*)
Back-up (or Connect to the constant
accessory) 12 V supply terminal.
16. Red (5*) 17. Red (4*)
Accessory Connect to terminal controlled by
(or back-up) ignition switch (12 V DC).
18. Orange/white
Connect to lighting switch terminal.
19. Black (chassis ground)
Connect to a clean, paint-free metal location.
21. Yellow/black
20. ISO connector
Note If you use an equipment with Mute
In some vehicles, the ISO connector may be function, wire this lead to the Audio Mute
divided into two. In this case, be sure to lead on that equipment. If not, keep the
connect to both connectors. Audio Mute lead free of any connections.
26.To subwoofer
29.Connect with RCA cables
output
(sold separately)
6. Wired remote input
Hard-wired remote
27.To rear output
control adaptor can
be connected (sold
separately).
28.To front output
8.IP-BUS input (Blue)
10.Multi-CD player
9.IP-BUS cable
(sold separately)
31.System remote control
22. Blue/white
Connect to system control terminal of the
power amp (max. 300 mA 12 V DC).
32. Front speaker
23. Blue/white (7*)
Connect to auto-antenna relay control
33. Rear speaker
terminal (max. 300 mA 12 V DC).
24. Blue/white (6*)
The pin position of the ISO
34. Subwoofer
connector will differ depends on the
type of vehicle. Connect 6* and 7*
when Pin 5 is an antenna control
35. Perform these connections when
type. In another type of vehicle,
using the optional amplifier.
never connect 6* and 7*.
36. Notes
25. Speaker leads
• Change the initial setting of this unit (refer to the
White: Front left
operation manual). The subwoofer output of this unit is
White/black: Front left
monaural.
Gray: Front right
• When using a subwoofer of 70 W (2 Ω), be sure to
Gray/black: Front right
connect with Violet and Violet/black leads of this unit.
Green: Rear left or subwoofer
Do not connect anything with Green and Green/black
Green/black: Rear left or subwoofer
leads.
Violet: Rear right or subwoofer
Violet/black: Rear right or subwoofer

Connecting the units

Note
30.Power amp • When this unit is installed in a vehicle without
(sold separately) ACC (accessory) position on the ignition switch,
red cable must be wired to the terminal that can
detect the operation of the ignition key. Otherwise,
battery drain may result.
30.Power amp
(sold separately)
30.Power amp
(sold separately)
ACC position No ACC position
• Use this unit in other than the following
conditions could result in fire or malfunction.
— Vehicles with a 12-volt battery and negative
grounding.
— Speakers with 50 W (output value) and 4 ohm
to 8 ohm (impedance value).
• To prevent short-circuit, overheating or
malfunction, be sure to follow the directions
below.
32. Front speaker
— Disconnect the negative terminal of the
battery before installation.
— Secure the wiring with cable clamps or
adhesive tape. To protect the wiring, wrap
adhesive tape around them where they lie
33. Rear speaker
against metal parts.
— Place all cables away from moving parts, such
as gear shift and seat rails.
— Place all cables away from hot places, such as
34. Subwoofer
near the heater outlet.
— Do not pass the yellow cable through a hole
into the engine compartment to connect to a
battery.
— Cover any disconnected cable connectors with
insulating tape.
— Do not shorten any cables.
— Never cut the insulation of the power cable of
this unit in order to share the power to other
equipment. Current capacity of the cable is
limited.
— Use a fuse of the rating prescribed.
— Never wire the speaker negative cable directly
to ground.
— Never band together multiple speaker's
negative cables.
English Connecting the units
• Control signal is output through blue/white cable Connection Diagram
when this unit is powered on. Connect it to an
1. This product
external power amp's system remote control or
2. Rear output
the vehicle's auto-antenna relay control terminal
(max. 300 mA, 12 V DC). If the vehicle is equipped 3. Front output
with a glass antenna, connect it to the antenna
4. Subwoofer output
booster power supply terminal.
5. Antenna jack
• Never connect blue/white cable to external power
6. Wired remote input
amp's power terminal. Also, never connect
Hard-wired remote control adaptor can be
it to the power terminal of the auto antenna.
connected (sold separately).
Otherwise, battery drain or malfunction may
7. Fuse (10 A)
result.
• IP-BUS connectors are color-coded. Be sure to 8. IP-BUS input (Blue)
connect connectors of the same color.
9. IP-BUS cable
• Black cable is ground. This cable and other
10. Multi-CD player (sold separately)
product's ground cable (especially, high-current
11. Note
products such as power amp) must be wired
Depending on the kind of vehicle, the function
separately. Otherwise, fire or malfunction may
of 3* and 5* may be different. In this case, be
result if they are accidentally detached.
sure to connect 2* to 5* and 4* to 3*.
12. Connect leads of the same color to
each other.
13. Cap (1*)
Do not remove cap if this terminal is not in use.
14. Yellow (3*)
Back-up (or accessory)
15. Yellow (2*)
Connect to the constant 12 V supply terminal.
16. Red (5*)
Accessory (or back-up)
17. Red (4*)
Connect to terminal controlled by ignition
switch (12 V DC).
18. Orange/white
Connect to lighting switch terminal.
19. Black (chassis ground)
Connect to a clean, paint-free metal location.
20. ISO connector
Note
In some vehicles, the ISO connector may
be divided into two. In this case, be sure to
connect to both connectors.
21. Yellow/black
If you use an equipment with Mute function,
wire this lead to the Audio Mute lead on that
equipment. If not, keep the Audio Mute lead
free of any connections.
22. Blue/white
Connect to system control terminal of the
power amp (max. 300 mA 12 V DC).
23. Blue/white (7*)
Connect to auto-antenna relay control terminal
(max. 300 mA 12 V DC).
English
24. Blue/white (6*)
The pin position of the ISO connector will differ
depends on the type of vehicle. Connect 6*
and 7* when Pin 5 is an antenna control type.
In another type of vehicle, never connect 6*
and 7*.
25. Speaker leads
White: Front left
White/black: Front left
Gray: Front right
Gray/black: Front right
Green: Rear left or subwoofer
Green/black: Rear left or subwoofer
Violet: Rear right or subwoofer
Violet/black: Rear right or subwoofer
26. To subwoofer output
27. To rear output
28. To front output
29. Connect with RCA cables (sold separately)
30. Power amp (sold separately)
31. System remote control
32. Front speaker
33. Rear speaker
34. Subwoofer
35. Perform these connections when using the
optional amplifier.
36. Notes
• Change the initial setting of this unit (refer
to the operation manual). The subwoofer
output of this unit is monaural.
• When using a subwoofer of 70 W (2 Ω), be
sure to connect with Violet and Violet/black
leads of this unit. Do not connect anything
with Green and Green/black leads.