WolfVision VZ-3 Bedienungsanleitung Seite 9

DVI/RGB Output
The DVI-I output (#5) can output analog and digital signals in following formats:
- XGA
- SXGA-
- WXGA*
- WXGA
- 720p
The "Auto resolution" function is activated by default. In this mode the Visualizer continuously checks
which devices are connected to the DVI-I output and automatically sets the optimal output mode for each
connected device separately.
connected units or the cables are not "Plug and Play" compatible. If the Visualizer can not detect the
resolution of the connected device, the output is set to the default of SXGA-/60Hz.
If you can not use the "Auto resolution" function, you can select the output mode manually in the on-screen
menu of the Visualizer (see page 10).
In order to achieve the best picture quality you must set the outputs of the Visualizer to match the native
resolution of your display unit (e.g. LCD or DLP projector or monitor).
Important: What matters is the native resolution of the projector or monitor, not the maximum resolution that
it can display (in compressed mode). The native resolution is the actual number of pixels of the built-in LCD
display or DLP chip of a projector or monitor. Most LCD or DLP projectors can also display higher
resolutions than their native resolution, but only in compressed mode and with inferior picture quality.
Do NOT set the output of the Visualizer to a higher standard than the native resolution of your
display unit!
Do not set a higher refresh rate than your monitor or projector can display, otherwise the monitor or
projector can be damaged!
Follow the instructions in the user manual of the connected units.
DVI-I Port
The DVI Port (#5) supplies the digital and analog signal - DVI-I.
Pin 8
Pin 1
Pin 9
Pin 17
Pin 24
Use supplied cable without choke (ferrit core), other cables may block the hinge mechanically.
(4:3 - 1024x768 pixels) at 60Hz
(4:3 - 1280x960 pixels) at 60Hz
(16:10 - 1280x800 pixels) at 60Hz
(16:9 - 1360x768 pixels) at 60Hz
(16:9 Widescreen HD - 1280x720 pixels) at 60 Hz
Please note that the Visualizer can not check the possible resolution, if the
1 - T.M.D.S. Data2-
2 - T.M.D.S. Data2+
3 - T.M.D.S. Data2/4 Shield
4 - T.M.D.S. Data4- (*)
C1 C2
5 - T.M.D.S. Data4+(*)
6 - DDC Clock
7 - DDC Data
C3 C4
C5
8 - Analog Vertical Sync
C1 - Analog Red
C4 - Analog Horizontal Sync
C5 - Analog Ground
(analog R, G & B return)
Choosing the Correct Output Mode
9 - T.M.D.S. Data1-
10 - T.M.D.S. Data1+
11 - T.M.D.S. Data1/3 Shield
12 - T.M.D.S. Data3- (*)
13 - T.M.D.S. Data3+ (*)
14 - +5V Power
15 - Ground (return for +5V,
HSync and Vsync)
16 - Hot Plug Detect
C2 - Analog Green
8
native resolution
native resolution
native resolution
17 - T.M.D.S. Data0-
18 - T.M.D.S. Data0+
18 - T.M.D.S. Data0+
19 - T.M.D.S. Data0/5 Shield
20 - T.M.D.S. Data5- (*)
21 - T.M.D.S. Data5+ (*)
22 - T.M.D.S. Clock+
23 - T.M.D.S. Clock-
24 - Analog Vertical Sync
C3 - Analog Blue m
*...not used