Inhaltsverzeichnis
Werbung
CD CHANGER
Warning!
HiFi A/V SURROUND
MINI SYSTEM
1 This set is designed for conventional CDs. Do
not use any accessories like disc stabilizer rings
or CD treatment sheets, etc, which may damage
2
3
the CD mechanism.
1
2 Do not load more than one disc into each tray.
3 When the CD changer is loaded with CD(s), do
not turn over or shake the unit as this may jam
the changer mechanism.
TIMER
You can load up to three discs in the CD changer
for continuous play without interruption. In addition
to the conventional 12-cm disc, 8-cm discs can also
be used without an adaptor .
ON/OFF
M37-DC
Loading the CD Changer
1 Press CD to select CD
2 Press OPEN/CLOSE
.
?
– The CD compartment slides out.
3 Load a disc with the printed side up in the right tray.
• You can load another disc in the left tray.
• To load the third disc, press the corresponding DISC SELECT button of the empty tray.
– The CD changer carousel will rotate until the empty tray is at the right hand side and is ready for
loading.
– Playback will always start with the outer right disc tray.
4 Press OPEN/CLOSE
to close the CD tray.
?
– The total number of tracks and playing time of the last selected disc appear on the display.
The following display indications will help you to know whether the disc trays are empty or loaded.
– indicates the disc tray is empty.
1
– indicates the disc tray is loaded with a disc.
2
– indicates the current or selected disc tray.
3
CD CHANGER
Programming Tracks
Programming tracks of a loaded CD is possible in the
stop mode of the CD. The display will indicate the
total tracks stored in the program. Up to 40 tracks can
be stored in the memory in any order. When 40 tracks
are stored and you attempt to store another track, the
display will show "PROGRAM FULL".
1 Load the desired discs in the disc trays.
1
FRONT
2
CD
3
2 Press PROGRAM to start programming.
SHUFFLE
– The
flag flashes on the display.
PROGRAM
3 Press the desired disc button to select the disc.
4 Press S or T to select the desired track.
5 Press PROGRAM to store the track.
• Repeat steps 3 to 5 to store other discs and
tracks.
6 Press 9 once to end programming mode.
– The total number of tracks programmed and total
playing time appear on the display.
Playing the program
1 Press B (or PLAY 2 on the remote control) to
CD TAPE
start program playback.
– "PROGRAM PLAY" appears on the display.
DUBBING
– The track number and elapsed playing time of
the current track will appear on the display.
2 Press 9 (or STOP 9 on the remote control) to
stop program playback.
1
2
Note : If you press any of the DISC SELECT buttons, the
3
set will play the selected disc, the stored program will
be ignored temporary. The
flag will also
PROG
temporarily disappear from the display and then re-
appear when the playback for the selected disc ends.
1
FRONT
Reviewing the program
2
CD
RECORD
3
Reviewing of program is only possible in the stop
SHUFFLE
mode.
• Press S or T repeatedly to review the
programmed tracks.
3
1
2
OPEN/CLOSE
3- di s c
C D C H A N G ER B I T C H EC K D I G I TA L TO A N A LO G U E
VOLUME
1
FRONT
2
CD
PROG
RECORD
PROGRAM
DEMO
3
SHUFFLE
SHUFFLE
CLEAR
INFRARED
R D S
SENSOR
ON
P HA NT OM
DOLBY PRO LOGIC
CD
TUNER
TAPE 1/2
AUX
INCREDIBLE
DBB
DSC
OF F
3 -ST ER EO
SURROUND
DOLBY SURROUND
P R O
L O G I C
B NR
HiFi A/V SURROUND
1
2
3
MINI SYSTEM
OPEN/CLOSE
TIMER
3-disc
2
CD CHANGER BITCHECK DIGITAL TO ANALOGUE
1
3
INFRARED
R D S
SENSOR
ON/OFF
O N
P HAN TOM
DOLBY PRO LOGIC
CD
TUNER
AUX
INCREDIBLE
DBB
DSC
SURROUND
O FF
3 -STEREO
M37-DC
DOLBY SURROUND
P R O
L O G I C
B NR
Erasing the program (in the stop position)
• Press CLEAR.
– "PROGRAM CLEARED" appears on the display.
Note : The program is also erased when the set is
disconnected from the power supply. If the CD
carousel is opened, the tracks belonging to the
outer two trays will be erased and "CLEARED" will
scroll on the display once.
PROGRAM
CD Synchro Start Recording
During CD synchro start recording,
• It is not advisable to fast forward/rewind your
cassette in TAPE DECK 1.
• It is not possible to listen to another sound source.
1 Press CD to select CD.
2 Load a disc into the disc tray.
3 You can program the tracks in the order you
want them to be recorded (see Programming
Tracks). If not, the tracks are recorded
according to the selected disc.
4 Press TAPE 1/2 to select TAPE DECK 2.
FRONT
PLAY
MODE
5 Load a blank cassette (full spool to the left) into
SIDE
TAPE DECK 2.
6 Press SIDE to select the front side of the tape.
– The
flag appears in the display.
FRONT
7 Press PLAY MODE to select the play mode ( å
FRONT
or ∂ ) for TAPE DECK 2.
REC
8 Press CD 2 TAPE to start recording.
– The
flag flashes on the display.
RECORD
– The CD starts playing after a seven-second
delay to prevent recording on the leader tape at
the beginning of the tape.
PROG
PROGRAM
9 Press 9 to stop recording.
CLEAR
CD CHANGER
Playing a Disc
1 Press B (or PLAY 2 on the remote control) to
1
FRONT
start playback.
2
CD
RECORD
3
– The disc tray, track number and elapsed playing
SHUFFLE
time of the current track appear on the display.
• To interrupt play, press ; (or PAUSE ; on the
remote control).
– The playing time flashes.
• To resume play, press B again (or PLAY 2 on
the remote control).
1
FRONT
2
CD
RECORD
3
2 To stop play, press 9 (or STOP 9 on the remote
SHUFFLE
control).
Note : All the available discs will play once, then
stop. When the CD has stopped playing, the set
will switch to the standby mode after 15 minutes if
no button is pressed.
When the CD tray is closed, you can play a CD
1
2
CD
directly by pressing the DISC SELECT (1 – 3) buttons.
RECORD
3
The CD player will stop at the end of playback of
SHUFFLE
the selected disc.
Selecting a desired track
Selecting a desired track at the stop mode
1 Press S or T ( PREV ¡ or NEXT ™ on the
remote control) until the desired track appears on
the display.
2 Press B (or PLAY 2 on the remote control) to
start playback.
– The selected track number and elapsed playing
time appear on the display.
Selecting a desired track during play mode
1 Press S or T ( PREV ¡ or NEXT ™ on the
remote control) until the desired track appears on
the display.
– The selected track number and elapsed playing
time appear on the display.
• If you press S once it will skip to the beginning
of the current track and play the track again.
CLOCK SETTING
TIMER
TIMER SET
TIMER SET
TIMER
SET CLOCK
TIMER
INFRARED
SENSOR
TIMER SET
Setting the clock
The clock will display in 24-hour mode, e.g.
00:00 or 23:59.
1 Press TIMER
˚
.
– "00:00" starts flashing.
TIMER SET
2 Press SET CLOCK.
TIMER
3 Set the hour with 4 or 3.
4 Set the minute with Q or R.
5 Press SET CLOCK again to store the setting.
– The clock starts running.
Note:
– When a power interruption occurs, the clock
settings are erased, and "0:00" will flash on the
display.
– To set the time with RDS clock, see "RECEIVING
RDS RADIO STATION" under TUNER section.
Setting the Timer
• The system can switch on to CD, TUNER or
TAPE 1 mode automatically at a preset time.
It can serve as an alarm to wake you up.
After half an hour from the preset time, the
system will return to the standby mode if no
button is pressed.
• Before setting the timer, make sure the clock is
set correctly.
• The timer works only once for each setting.
• The volume of the timer will be at the last
setting before the set is switched off.
Searching for a particular passage
during playback
• Press and hold S or T (5 or 6 on the
remote control) until the desired passage is
located. During the search, the sound is played
at a faster than normal rate and at a reduced
volume. Playback returns to normal when S
or T is released.
Shuffle
PROGRAM
SHUFFLE – playing all the available discs and their
tracks in random order. It can also be used when
CLEAR
tracks are programmed.
To shuffle all the discs and tracks
1 Press SHUFFLE on the unit or on the remote control.
– "SHUFFLE" flashes briefly on the display.
– The
flag, the disc and the track selected
SHUFFLE
FRONT
at random appear on the display.
SHUFFLE
• The discs and the tracks will now be played in
random order until you press 9.
2 Press SHUFFLE again to resume normal play.
– The
flag disappears from the display.
SHUFFLE
TIMER SETTING
Timer Setting
1 Press TIMER
˚
.
TIMER
2 Press TIMER SET.
– The
flag flashes.
TIMER
3 Press 4 or 3 to select the desired source.
– The display will switch as follows:
TUNER –> CD –> TAPE 1 –> TUNER .
TIMER
4 Press TIMER SET to confirm your selection.
– The display will show " ON 00:00 " and
"00:00" flashes.
5 Press 4 or 3 to set the hour for the timer to start.
6 Press Q or R to set the minutes for the timer
to start.
SET CLOCK
7 Press TIMER SET to store the start time.
– The TIMER is now set.
– The
flag remains lit.
TIMER
To stop the timer
1 Press TIMER
˚
.
SET CLOCK
2 Press TIMER on the set.
RDS
MODE
– The TIMER is now off.
To start the timer again
1 Press TIMER
˚
.
2 Press TIMER on the set.
– The display will show the last set start time of the
TIMER and its flag.
– The
flag remains lit.
TIMER
Notes:
1 If the source selected is TUNER, the last tuned
frequency will be switched on.
2 If the source selected is CD, the first track of the
last selected disc will be played. If the CD trays
are empty, the TUNER source will be selected
instead.
3 If the source selected is TAPE 1, and the preset
time is reached during high speed dubbing, the
TUNER source will be selected instead.
Werbung
Inhaltsverzeichnis
