Inhaltsverzeichnis
Werbung
OPERATING THE SYSTEM
TIMER
CD TAPE
1
FRONT
D PRO LOGIC
D 3 STEREO
PLAY
2
CD
STEREO
BACK
PHANTOM
PROG
MODE
NORMAL
RECORD
D NR
SHUFFLE
DBB
PROGRAM
DEMO
TIMER SET
3
SET CLOCK
SW
LW
FMMW
HSD
REC
AMPM
TIMER
DUBBING
SIDE
BAND
RDS
SHUFFLE
MODE
TIMER
CLEAR
PRESET
TUNING
INFRARED
R D S
SENSOR
ON/OFF
ON
CD
TUNER
TAPE 1/2
AUX
INCREDIBLE
DBB
DSC
OFF
SURROUND
M37-DC
DOLBY SURROUND
P R O
L O G I C
Important :
Selecting the Sound Source
Before you begin operating the system, complete
• Press the respective source selection: CD,
the preparation procedures.
TUNER, TAPE 1/2 or AUX on the set or the
The set is in the DEMO mode when the AC
remote control.
power plug is connected to the wall socket.
– The display indicates the selected sound source.
Note : For AUX source, ensure that you had
Switching the system ON
connected the audio left and right output terminals
• Press ON/OFF
y
, CD, TUNER, TAPE 1/2 or
of the external equipment (TV, VCR or Laser Disc
AUX (or CD, TUNER, TAPE 1 or TAPE 2 on
player) to the AUX IN sockets.
the remote control).
Switching the system to standby mode
Demo mode
y
• Press ON/OFF
y
again (or
on the remote
The system has a demonstration mode that shows
control).
the various features offered by the system.
– The clock time appears on the display during
• Press DEMO to switch on the demonstration.
3 seconds and then switches off in order to
– The display will show "DEMO", then a
bring down power consumption to a
demonstration of the the various features will
minimum.
follow.
• If you wish the time to be indicated conti-
• Press DEMO again or ON/OFF
˚
nuously in standby mode, press TIMER
.
remote control) to stop the demonstration mode.
DOLBY PRO LOGIC
When you have completed the Dolby Pro Logic
setup, you are ready to experience and enjoy a
FRONT
Home Cinema sound ambience
LEFT
TV
• Press DPL MODE on the remote control
repeatedly to select and cycle through the
various sound modes:
Dolby Pro Logic Center Normal –> Dolby
Pro Logic Center Phantom –> Dolby 3 Stereo
–> Stereo –> Dolby Pro Logic Center Normal
SURROUND
LEFT
–> etc.
• You can also press the
respective DOLBY PRO
ON
PH ANTOM
DOLBY PRO LOGIC
FRONT
LOGIC button on the set
LEFT
TV
to select the Dolby Pro
OFF
3-S TER EO
Logic sound modes.
• For the best Dolby Pro Logic sound, it is
recommended to select the setting CLASSIC
with the DSC button and not to use
INCREDIBLE SURROUND
Dolby Pro Logic Center Normal
CENTRE
HIFI MINI
SYSTEM
Choose this setting for playback of music and
FRONT
LEFT
movies (especially Laser Discs, videocassettes and
TV
TV broadcasts with DOLBY SURROUND sound).
Not only does Dolby Pro Logic surround you with
sound, it also gives you a clear perception of the
position and direction of the sound.
In this mode you use 5 speakers: front left and right,
a center speaker and two surround speakers.
SURROUND
LEFT
• Press the DOLBY PRO LOGIC ON key on the
set or the DPL MODE key on the remote
control to select this setting.
FRONT
LEFT
– The message DOLBY PROLOGIC scrolls once
TV
on the display. The
flags
d
PRO LOGIC NORMAL
stay on the display.
Sound control
Volume Adjustment
VOLUME
• Rotate VOLUME right or left (or press VOLUME +
or – on the remote control) to increase or
decrease the sound level.
For Personal Listening
p
• Connect the headphones jack to the
socket
(3.5 mm) at the front of the set. The speakers will
be muted.
PHAN T OM
DOLBY PRO LOGIC
Digital Sound Control (DSC)
The DSC feature creates a realistic atmosphere for
3 - ST EREO
the style of music you select using the latest digital
sound technology.
B NR
• To enjoy a special sound effect, press the DSC
button on the unit or the remote control several
times. The display shows the selected effect:
JAZZ
, CLASSIC
, ROCK
, POP
or OPTIMAL.
• In the setting OPTIMAL you hear the sound
setting that is tuned to the acoustics of the
supplied speakers.
Dynamic Bass Boost (DBB)
• Press DBB to enhance the bass response.
– The
flag lights up.
DBB
Incredible Surround
• In additional to all other sound settings, you can
switch on or off the incredible surround sound
feature by pressing INCREDIBLE SURROUND.
– This creates a phenomenal surround sound effect
even if the speakers are positioned close to the
system. The sound becomes "incredibly" spatial.
– The INCREDIBLE SURROUND button lights up.
y
y
(or
on
Dolby Pro Logic Center Phantom
HIFI MINI
SYSTEM
Select this setting if you have not connected a
FRONT
RIGHT
center speaker, but still wish to simulate the
sound coming from the center.
• Press the DOLBY PRO LOGIC PHANTOM key
on the set or once again the DPL MODE key
on the remote control to select this setting.
– The message CENTER PHANTOM scrolls once
SURROUND
on the display. The
d
PRO LOGIC PHANTOM
RIGHT
flags stay on the display
CENTRE
HIFI MINI
SYSTEM
Dolby 3 Stereo
FRONT
RIGHT
Choose this setting for playback of music and movies
(especially Laser Discs, videocassettes and TV
broadcasts with DOLBY SURROUND sound),
when not using rear speakers. You get a clear
perception of the position and direction of the
sound.
In this mode you use only front and center
speakers, the rear speakers are not switched on.
• Press the DOLBY PRO LOGIC 3-STEREO key
FRONT
on the set or once again the DPL MODE key
RIGHT
on the remote control to select this setting.
– The message 3 STEREO scrolls once and the
3
flag stays on the display.
d
STEREO
Normal Stereo
SURROUND
RIGHT
In this case the center and rear speakers are
switched off for normal stereo operation.
HIFI MINI
• Press the DOLBY PRO LOGIC OFF key on the
SYSTEM
FRONT
set or once again the DPL MODE key on the
RIGHT
remote control to select this setting.
– The message STEREO scrolls once on the
display.
DOLBY PRO LOGIC
Dolby Pro Logic
Setting up the Dolby Pro Logic system
This state of the art Dolby Pro Logic mini system
A full Pro Logic system needs 5 speakers that should
enables you to experience and enjoy a Home
be connected and positioned as illustrated below.
Cinema sound ambience.
CENTRE
Dolby Pro Logic is a coding system that enables
a set to decode 4 sound channels out of a
normal stereo signal: the center channel for
FRONT
TV
LEFT
picture related sounds, both front left and right
channels for stereo sounds and one surround
channel for the rear to bring room and depth to
the scene.
The surround signal is reproduced by two
speakers placed towards the rear of the listening
area. Although the surround signal is mono, a
pair of speakers is necessary to produce the
correct diffused sound field.
Dolby Pro Logic manufactured under license from
SURROUND
LEFT
Dolby Laboratories Licensing Corporation.
DOLBY, the double-D symbol d and 'PRO
LOGIC' are trademarks of Dolby Laboratories
Licensing Corporation.
Positioning the center speaker
The center speaker should be placed in the center
General hints for speaker positioning
between both front speakers, e.g. underneath or on
Avoid positioning the speakers in a corner or on
top of the TV. The best height for the center speaker
the floor, as this will boost the bass tones too
is at the height of the listener's ears (while seated).
much. Placing the speakers behind curtains,
Note: to avoid interference with the TV picture, use
furniture etc. will reduce the treble response, thus
only a magnetically shielded center speaker.
reducing the stereo effect considerably. The
Positioning the surround speakers
listener should always be able to 'see' the
The surround speakers connected to the REAR LEFT
speakers.
terminals of the amplifier should be on the left and
Each room has different acoustic characteristics
the surround speaker connected to the REAR RIGHT
and the positioning possibilities are often limited.
terminals of the amplifier on the right side of the
You can find the best position for your speakers
listener in the room.
by following the picture on the right. The
speakers should always be arranged as
The surround speakers should face each other and
symmetrically as possible in the room.
be in line with, or at most 1.5m behind the listener.
TUNER
TIMER
FRONT
STEREO
RECORD
PROGRAM
DEMO
FM
TIMER
BAND
RDS
MODE
PRESET
TUNING
INFRARED
R D S
SENSOR
ON/OFF
O N
DOLBY PRO LOGIC
CD
TUNER
TAPE 1/2
AUX
INCREDIBLE
DBB
DSC
O FF
SURROUND
M37-DC
DOLBY SURROUND
P R O
L O G I C
Tuning to radio stations
FRONT
1 Press TUNER on the unit or on the remote control.
FM
– First TUNER appears on the display and after a
few seconds it will show the current frequency or
the station name if available.
The available display button functions light up:
2 Press BAND to select the desired waveband:
FRONT
STEREO
RECORD
FM, MW or LW.
FM
BAND
3 Press TUNING Q or R for more than one
PRESET
second.
– The display will show 'SEARCH' until a station
with sufficient signal strength is found.
FRONT
• Repeat this procedure until the desired station is
RECORD
FM
reached.
BAND
• To tune to a weak station, briefly press TUNING
PRESET
Q or R until the display shows the right
frequency and/or when the best reception has
been obtained.
• When tuning to a station in FM, the unit always
selects FM STEREO. If stereo reception is disturbed
you can press BAND again to select FM MONO.
Test tone
The test tone feature enables you to adjust the Front
left and right, the Center and Surround sound level
of the respective speakers in the Dolby Pro Logic
HIFI MINI
mode.
SYSTEM
We advise you to sit down at the normal listening
FRONT
position when performing this operation.
RIGHT
1 Switch on the set, for instance by pressing one
of the source keys on the remote control: CD,
TUNER, TAPE, AUX/TV.
2 Press TEST TONE on the remote control.
– You will now hear a test tone from the left,
center, right and rear speakers in turn, in a
repeating cycle.
– The test signal will last approx. 90 seconds.
3 Press L BALANCE to adjust the Front Left level
SURROUND
setting.
RIGHT
– The display shows BAL L +1 during 2 seconds.
During this time you can adapt the level with the
L BALANCE and BALANCE R keys.
4 Press BALANCE R to adjust the Front Right level
setting.
– The display shows BAL R -1 during 2 seconds.
During this time you can adapt the level with the
L BALANCE and BALANCE R keys.
5 Press CENTER + or – to adjust the center level
setting.
– The display shows e.g. CENT +1 or CENT -1.
6 Press REAR + or – to adjust the surround level
setting.
– The display shows e.g. REAR +1 or REAR -1.
7 When perception of all levels is equal, press
TEST TONE again to turn off the test tone.
Storing Preset Stations
You can store up to 20 stations in the memory. When
VOLUME
a preset station is selected, the preset number appears
next to the frequency on the display.
Automatic programming
1 Press TUNER on the unit or on the remote control.
2 Press PROGRAM for more than 1 second.
–
flashes and 'AUTO' is displayed.
PROGRAM
– Every available station will be stored automatically.
PH A NTOM
The frequency and preset number will be
displayed briefly.
3-STE REO
– It will stop searching when all the available stations
are stored or the memory for 20 preset stations is
used.
B NR
– The set will remain tuned to the last stored preset
number.
• You can cancel the automatic programming by
PROGRAM
pressing PROGRAM or 9.
Note: If you want to maintain some old preset
numbers, for example preset number 1 - 9, select
preset 10 before starting automatic programming:
now only the preset numbers 10 to 20 will be
programmed.
PROGRAM
RDS
Manual programming
MODE
TUNING
1 Press TUNER on the unit or on the remote control.
2 Press BAND to select the desired waveband: FM,
MW or LW.
3 Press TUNING Q or R to tune to the desired
PROGRAM
frequency.
4 Press PROGRAM for less than 1 second.
TUNING
–
flashes on the display.
PROGRAM
5 Press PRESET 4 or 3 to select a preset number.
6 Press PROGRAM again.
–
stops flashing, and the station is stored.
PROGRAM
• Repeat the above procedure to store other preset
stations.
Werbung
Inhaltsverzeichnis
