Renkforce FT0100 Bedienungsanleitung Seite 33

12/24 hour format:
• The display "12H" or 24H" flashes; set the desired format with the buttons "+" or "-".
In 12h mode, "PM" is displayed to the right of the time in the second half of the day.
Hour settings:
• Briefly push the "SET" button. The hours of the time flash. Set them with the buttons "+" and "-".
Minute settings:
• Briefly push the "SET" button. The minutes of the time flash. Set them with the buttons "+" and "-".
Each push of a button will also automatically reset the seconds to "00".
Date format:
• Push the "SET" button. You will enter the setting mode for the date format. Use the buttons "+" or "-" to
select the desired date format MM-DD-YY (month-day-year), DD-MM-YY (day-month-year) or YY-MM-DD (year-month-
day).
Month:
• Briefly push the "SET" button. The months of the date flash. Set them with the buttons "+" and "-".
Day:
• Briefly push the "SET" button. The days flash. Set them with the buttons "+" and "-".
Year:
• Briefly push the "SET" button. The years of the date flash. Set them with the buttons "+" and "-".
Max./Min. Setting:
• Briefly push the "SET" button. You will get to the setting max./min. Clearing. Choose between the
setting CLR ON and CLR OFF. For the setting CLR ON, the max./min. values are automatically deleted at midnight every
day. For the setting CLR OFF, the max./min. values can only be deleted manually. Set the desired mode with the buttons
"+" or "-".
Temperature unit:
• Briefly push the "SET" button. The display UNIT SET appears in the display and the temperature
unit flashes. Use the buttons "+" or "-" to choose between the temperature display °C or °F.
Barometric pressure unit:
•
metric pressure unit flashes. Use the buttons "+" or "-" to choose between the measuring units mb/hPa, mmHg or inHg
for barometric pressure.
Threshold barometric pressure:
•
tory settings 2). Use the buttons "+" or "-" to set the threshold 2-4 for the barometric pressure. Observe item "threshold
barometric pressure".
Threshold storm warning:
•
4). Use the buttons "+" or "-" to set the threshold 3 mbar/h - 9 mbar/h for storm warning. Also observe the item Storm
Warning on this.
Symbol weather forecast:
•
the buttons "+" or "-" to set the corresponding symbol, depending on the current weather situation.
Background colour:
•
OUT). The background colour of the weather station switches colour depending on the temperature of the outdoor
sensor 1 or the indoor temperature. A colour can also be set manually.
- Setting OUT: The temperature of channel 1 of the outdoor sensor is used for the automatic background colour of the
display.
- Setting IN: The indoor temperature is used for the automatic background colour of the display.
- Setting USE: Manual setting of the background colours (11 options).
- Set the desired mode with the buttons "+" or "-".
The following settings depend on the selection of OUT, IN or USE:
Setting OUT: Standard setting, see table
LOWER threshold OUT (standard -12.2 °C): Push the "SET" button; the temperature for the lower threshold flashes; change
this value with the buttons "+" or "-".
UPPER threshold OUT (standard 37.8 °C): Push the "SET" button; the temperature for the upper threshold flashes; change
this value with the buttons "+" or "-".
Briefly push the "SET" button. The display UNIT SET appears in the display and a baro-
Briefly push the "SET" button. Display WEATHER (2-4) appears in the display (fac-
Briefly push the "SET" button. Display STORM (3-9) appears in the display (factory setting
Briefly push the "SET" button. The symbol weather forecast appears in the display. Use
Briefly push the "SET" button. You will get to the settings for the backlighting (factory setting:
33