Pet Mate cat mate elite 355 Betriebsanleitung Seite 25

IMPORTANT:
• BEFORE INSTALLATION, PROGRAM CAT FLAP AS DESCRIBED IN
OPERATION INSTRUCTIONS
• DO NOT CUT TUNNEL OF CAT FLAPS.
1. Wood / Plastic / Metal Door Panels 0-50mm (0-2") Thick
1.1 Place exterior frame in desired position on door. We recommend the bottom
of the aperture is approximately 150mm (6") above ground level. (Fig. 1a/b).
If you must fit higher consider providing a step to help your cat enter.
1.2 Draw around the aperture (Fig. 1a), then using an electric jigsaw cut 5mm
( / ") outside of the line. (Fig. 2a).
3
16
Installation in metal doors: Draw around the OUTSIDE of the frame. (Fig.
1b). Using an electric jigsaw cut 12mm (
to instruction 1.6.
Be careful to cut hole square to the door, particularly with thicker doors.
Ensure interior frame is free fitting in hole.
1.3 Determine thickness of door panel, (t). (Fig. 3).
1.4 Holding the interior frame and the exterior frame in position, mark the 2 screw
holes. (Fig. 4).
1.5 Remove the frames and drill screw clearance holes in panel to 6mm (
diameter.
1.6 Position interior frame on inside of door and screw exterior frame to it by
using appropriate screws for panel thickness, (t), as shown in Fig. 6. If
necessary, cut supplied screws to length. Finally fit two screw caps.
1.7 For metal panels: DELETE DELETE DELETE DELETE DELETEDELETE
Product Ref. 305, 355, 356 - remove batteries for a minimum of 2 minutes
after installation. This will enable the cat flap to retune itself to its new location
for maximum performance.
Product Ref. 306 - remove battery cover and push electrical connector (E)
on to pins as shown in Fig. 5.
2. Glass Panels 0-50mm (0-2") Thick
2.1 We recommend that you ask a glazier to cut a hole of 232mm (9
in the position required and then install the cat flap as detailed below.
/ ") INSIDE the line (Fig. 2b) and go
1
2
DELETE DELETE DELETE DELETE DELETE
4
Alternatively, you may prefer to replace the glass panel with a clear plastic
panel and install as instructions 1.1 to 1.6.
Note: It is not possible to cut a hole in double glazed or toughened glass. You
will need a new panel with the hole already cut from your glazier.
2.2 Determine thickness of door panel, (t). (Fig. 3).
2.3 The black foam seal is not suitable for fitting to glass and should be removed.
If desired, the exterior frame may be sealed to the glass panel using silicone
sealant.
2.4 Position interior frame on inside of door, screw exterior frame to it by using
appropriate screws for panel thickness, (t), as shown in Fig. 6. If necessary,
cut supplied screws to length. Finally fit two screw caps.
3. Wall Fitting
If you are installing your cat flap in a wall, you will need to purchase Elite wall
liners. You will need 1 wall liner for every 50mm (2") of wall thickness over
50mm (2") for Product Ref. 305, 306, 307 or 100mm (4") for Product Ref. 355,
356 cat flaps.
3.1 Create a rectangular hole in your wall 205mm (8") high by 180mm (7") wide.
3.2 Remove interior frame battery cover by pushing up as shown,
(Fig. 7). Product Ref. 307 only: Remove the 4-way knob as shown in Fig.
12 using a thin screwdriver to lever off cover (A) as shown.
/ ")
3.3 Remove interior frame cover by unscrewing 2 screws in rear of interior frame
1
4
(Fig. 8). (Note: these screws may be discarded as it will be impossible to refit
them). Next remove the 2 screws under the battery cover and remove the
interior frame by pivoting down (Fig. 9).
3.4 Carefully remove 2 screw clips with pliers. (Fig. 10).
3.5 Fit interior frame assembled with requisite number of wall liners to interior
wall securing in position with 2 suitable screws as shown in Fig. 11. (Note:
you will need to fit a washer (not supplied) under the head of the screws). If
required, the wall liners may be glued in place, although a firm push fit will
usually suffice.
3.6 Refit interior frame cover with 2 screws under battery cover, taking great care
not to trap electrical wires. (Product Ref. 307 only: Refit the 4-way knob
using a hand screwdriver.) Replace the battery cover.
/ ") diameter
3.7 Fit exterior frame using 2 off 25mm (1") screws supplied and finally, fit
1
8
2 screw caps.
5