Declaration Of Conformity; Battery Charging - Berner BACJS 10,8 V LI Originalbetriebsanleitung

OBJ_BUCH-2438-002.book Page 17 Thursday, March 5, 2015 7:08 PM
An estimation of the level of exposure to vibration
should also take into account the times when the
tool is switched off or when it is running but not ac-
tually doing the job. This may significantly reduce
the exposure level over the total working period.
Identify additional safety measures to protect the
operator from the effects of vibration such as:
maintain the tool and the accessories, keep the
hands warm, organisation of work patterns.

Declaration of Conformity

We declare under our sole responsibility that the
product described under "Technical Data" is in
conformity with all relevant provisions of the direc-
tives 2009/125/EC (Regulation 1194/2012),
2011/65/EU, until 19 April 2016: 2004/108/EC,
from 20 April 2016 on: 2014/30/EU, 2006/42/EC
including their amendments and complies with the
following standards: EN 60745-1, EN 60745-2-11.
Technical file (2006/42/EC) at:
Berner Trading Holding GmbH,
Bernerstraße 6,
74653 Künzelsau, GERMANY
Armin Hess
Chairman of the Management Board
06.02.2015, Berner Trading Holding GmbH
Bernerstraße 6
74653 Künzelsau, GERMANY
Assembly
 Before any work on the machine itself (e. g.
maintenance, tool change, etc.) as well as dur-
ing transport and storage, remove the battery
from the power tool. There is danger of injury
when unintentionally actuating the On/Off
switch.

Battery Charging

 Use only the chargers listed in the technical
data. Only these battery chargers are matched
to the lithium-ion battery of your measuring tool.
Note: The battery supplied is partially charged. To
ensure full capacity of the battery, completely
charge the battery in the battery charger before us-
ing your power tool for the first time.
The lithium-ion battery can be charged at any time
without reducing its service life. Interrupting the
charging procedure does not damage the battery.
1 619 P12 703 • 5.3.15
The lithium-ion battery is protected against deep
discharging by the "Electronic Cell Protection
(ECP)". When the battery is empty, the machine is
switched off by means of a protective circuit: The
inserted tool no longer rotates.
Observe the notes for disposal.
Battery Charge-control Indication
The three green LEDs of the battery charge-control
indicator 5 show the charging status of the battery
1. The battery charge-control indicator only illumi-
nates for 5 seconds after start-up.
LED
Continuous lighting 3 x green
Continuous lighting 2 x green
Continuous lighting 1 x green
Flashing light 1 x green
Flashing light 3 x green
When no LED lights up after switching on, then the
battery is defective and must be replaced.
Replacing/Inserting the Saw Blade
 When mounting the saw blade, wear protec-
tive gloves. Danger of injury when touching the
saw blade.
Selecting a Saw Blade
Use only T-shank saw blades. The saw blade
should not be longer than required for the intended
cut.
Use a thin saw blade for narrow curve cuts.
Inserting the Saw Blade (see figure A)
 Clean the shank of the saw blade before in-
serting it. An unclean shank cannot be fastened
securely.
Insert the saw blade 14 into the stroke rod 11 until
it latches. The SDS lever 18 automatically snaps to
the rear and the saw blade is locked. Do not man-
ually press the lever 18 toward the rear, otherwise
you could damage the machine.
While inserting the saw blade, pay attention that
the back of the saw blade is positioned in the
groove of the guide roller 10.
 Check the tight seating of the saw blade. A
loose saw blade can fall out and lead to injuries.
Ejecting the Saw Blade (see figure B)
 When ejecting the saw blade, hold the ma-
chine in such a manner that no persons or an-
imals can be injured by the ejected saw blade.
Turn the SDS lever 18 forward towards the contact
protector 19 to the stop. The saw blade is released
and ejected.
Capacity
2/3
1/3
<1/3
Reserve
Empty
English | 17