Introduction; General Information - LD Systems LDCURV500TS Bedienungsanleitung

The warning triangle with lightning symbol indicates dangerous uninsulated voltage inside the unit, which may cause an
electrical shock.
The warning triangle with exclamation mark indicates important operating and maintenance instructions.
Warning! This symbol indicates a hot surface. Certain parts of the housing can become hot during operation. After use, wait for
a cool-down period of at least 10 minutes before handling or transporting the device.
Warning! This device is designed for use below 2000 metres in altitude.
Warning! This product is not intended for use in tropical climates.
CAUTION! HIGH VOLUMES IN AUDIO PRODUCTS!
This device is meant for professional use. Therefore, commercial use of this equipment is subject to the respectively applicable national
accident prevention rules and regulations. As a manufacturer, Adam Hall is obligated to notify you formally about the existence of potential
health risks.
Hearing damage due to high volume and prolonged exposure: When in use, this product is capable of producing high sound-pressure levels
(SPL) that can lead to irreversible hearing damage in performers, employees, and audience members. For this reason, avoid prolonged
exposure to volumes in excess of 90 dB.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.

INTRODUCTION

The compact, highly portable CURV 500® Touring Array System is fully scalable with up to four interlocking aluminium unibody line array
elements operating on a SmartLink® plug and play adapter. It comes with two standard CURV satellites that feature a single 4" midrange and
triple 1" high frequency drivers using LD Systems' WaveAhead® technology, and two duplex satellites with twice the speaker complement.
The ported 15" subwoofer base includes the CURV 500® Touring Array System's class D amplification with multiband limiter, short circuit,
thermal and overcurrent protection. It sports comprehensive connectivity on combo and Neutrik speakON connectors, six DSP presets for quick
system configuration, an M20 pole mount and three ergonomic handles for easy portability. Providing impressive versatility, the lightweight
CURV 500® Touring Set delivers high definition audio with powerful punch, superb balance and extended vertical and horizontal coverage. The
set includes a subwoofer pole and dedicated speaker cable.

General information

Before using, the subwoofer of the LD Systems CURV 500
the system on a trolley as there is a risk of the entire system beginning to move uncontrollably. This can result in an accident and/or
damage. In order to ensure sufficient cooling, a space of at least 50 cm must be left between the back of the subwoofer and other surfaces
such as walls. Please take care to connect audio and power cables correctly when using the system and devices such as CD players and
mixing desks which are connected to it. Only use intact cables with a suitable diameter and always unroll cable reels to their full length. If
necessary, use cable protectors to avoid tripping hazards caused by loose cables. Never place the device directly on an edge. Do not place
the subwoofer on a table. To avoid unwanted noises when switching on connected devices, always ensure the system is the last device to
be switched on and the first to be switched off.
4
CAUTION:
To reduce the risk of electric shock, do not remove cover (or back). There are no user serviceable parts
inside. Maintenance and repairs should be exclusively carried out by qualified service personnel.
touring array system must be placed on its feet on a flat surface. Never operate
®