Steinbach 061018 Bedienungsanleitung Seite 7

EN
B: Cover
C: Filter unit
D: Motor
E: Filter tank
F: Side cover
G: Side cap
H: Floats
I: Filter
J: Drive belt
K: Cleaning roller
L: Power cable
Preparation
Attach cable hanger
Hook the cable hooks (Fig. 4) onto the hanging ring on the cover of
the cleaner. Place the cleaner into the water, while holding onto the
hanging ring (Fig, 5). Once all the air has escaped from the cleaner
(Fig, 6), (the cleaner must be completely free of air, otherwise nor-
mal operation will be affected), it will sink to the bottom on its own
(Fig. 7).
Caution: For optimal performance, make sure that there is no more
air in the cleaner (air bubbles stop coming out of the cleaner, and it
stays on the pool floor properly).
Connecting the power source
When the cleaner is completely on the pool floor (Fig. 8-10), take the
power cable, roll it out fully and push the plug into the socket on the
electricity control box. Then connect the cable to the socket (Please
note when connecting cables that the plugs are in the right direction
and position in relation to each other), and tighten the nuts on both
sides. Connect the mains cable to the power source. The swimming
pool cleaner is now ready for use.
Description of operating unit, Fig. 11
No.: Symbol Display
1 Power LED for power
2 30s
3 60s
Function LED
4 90s
5 120s
Display 3 hours auto-
6
matic operation
Automatic operation 3
7 3h
hours
Display 5 hours auto-
8
matic operation
Automatic operation 5
9 5h
hours
Display for manual op-
10
eration
Manual forward / back-
11 FWD/REW
wards movement
12 Display for standby
Cleaner is in standby
13 Power On
mode
14 Power Off The cleaner stops.
Example 3 hours automatic operation
You will find a description of how to program the cleaner for 3 hours
automatic operation below:
Press the button "Power On" and the LED lights up on the operation
panel. The cleaner is now in standby mode.
When you press the 3h operation button, LED 6 and 2 (as pre illus-
tration)light up, and the floor cleaner will run automatically for 3
hours.
Speedcleaner RX5 | 2016_V1
Function
Lights up when switched
on
In manual mode, all LED's
light up periodically. In au-
tomatic mode, the program
duration set is shown
Press to start 3 hours au-
tomatic operation.
Press to start 5 hours au-
tomatic operation.
Press 1 x: Cleaner moves
forwards, press again,
cleaner stops, press again,
cleaner goes backwards.
Press 1 x, unit stays in
standby mode.
The function LED's now alternate regularly between 30, 60, 90, and
120 seconds. The cleaner goes forward for 30 seconds, backwards
for 60 seconds, forward for 90 seconds, and backwards for another
120 seconds.
The unit switches off automatically after 3 hours.
Warning
In the event of a fault, the display LED flashes.
Flashing LED Cause and solution
30, 60, 90, 120 The cleaner is out of the
seconds pool and is not taking any
water in.
120 seconds No connection to the op-
erating unit, please con-
nect the cable and check
the plug connection.
All displays light Fault in the pump. Contact
up an expert.
90 seconds Fault in the power pack.
Contact an expert.
Caution: Before removing the cleaner from
the pool, make sure that the electricity is fully
switched off.
Preparation
Care and maintenance
The cleaner turns itself off automatically after a cleaning cycle. Un-
plug the mains cable, gently pull the cable, and lift the cleaner out of
the water using the ring on the clamp nut.
Caution:
When lifting the cleaner out of the water, you must ensure that the
cleaner does not hit the side of the pool wall, otherwise you may
damage both the cleaner and the liner.
Before the cleaner clears the surface of the water, it must be held
there for 10 to 15 seconds, so that most of the water can flow out of
the water outlet into the pool. Only then should you put the cleaner
on the edge of the swimming pool.
Finally lift the cleaner out of the pool by the handle, leaving the cable
hook submerged on the cable hanger. Fig. 12, 13.
It is important to place the cleaner near the edge of the pool, then
open the cover screws and remove the housing cover. Now take out
the filter unit and remove the filter bag.
When cleaning the filter bag, you must remove the dirt from the out-
side of the bag with clean water. Fig. 14. Then put the bag back in.
As a water outlet with filter is built into the cleaner, some dirt may
remain in the cleaner, which should also be rinsed out. Then you
should put the filter unit back in completely along the motor.
Caution: There is a positioning pin on the top of the filter housing,
please do not mount this incorrectly! Fig. 15.
After mounting the housing cover, the cover screws must be re-
fitted.
Caution: To avoid any negative effect on the performance of the
cleaner, make sure that the cover is properly attached to the base
housing. To avoid any damage, please make sure that the cable is in
the correct position. Fig. 16.
Page 7 of 56