Preparing Hot Water; Changing And Saving The Cup Measure - AEG Electrolux CP 2 Serie Gebrauchsanweisung

822_949_318 CP2..._defnep.book Seite 37 Freitag, 2. November 2007 6:30 18
1 Caution! Risk of impurities through
dried on milk residues in the steam
nozzle. Take care not to immerse the
steam nozzle in the milk far enough to
cover the air intake opening at the top
of the steam nozzle. Otherwise milk
can be sucked into the nozzle and
cause impurities in the steam nozzle.
0 Turn the Selection dial for steam and hot
water (Fig. 1, D) to the
(Fig. 17). The milk is now frothed up.
3 Hold the mug steady during the froth-
ing. The nozzle should not be allowed
to touch the bottom of the mug and
cut off the steam supply. Froth the milk
to at least twice its volume.
0 To stop frothing, turn the Selection dial
for steam and hot water (Fig. 1, D) to
the position and remove the jug
(Fig. 17).
1 Caution! Danger of scalding from hot
milk spray! Switch the steam off,
before removing the jug with the
frothed milk.
0 To finish steam mode, press the "Steam
Pre-selector" key (Fig. 3, g)
ca. 60 sec., for the machine to auto-
matically return to the coffee mode.
The indication is extinguished.
The coffee machine is now ready for
making coffee again.
0 Each time you have frothed milk, let
off some hot water through the nozzle
for a short time by setting the Selec-
tion dial for steam and hot water (Fig.
1, D) to the
essary to prevent milk residues drying
inside the nozzle, and thereby blocking
it. Use a suitable container to catch the
water. Afterwards turn the Selection
dial for steam and hot water (Fig. 1, D)
back to the position
0 Remove the frothing aid after each use
(Fig. 18). For this, take hold of the
frothing aid by the black seal and dis-
engage the bayonet connector by
turning it slightly anticlockwise. Rinse
off the milk residues under running
water. Wipe the steam nozzle off with
a damp cloth.
1
8
position
1
0 Place a container under the hot water
0 After you have dispensed the hot water
9
, or wait
position. This is nec-
0 Repeatedly press the "Cup Size" key
0 Place the appropriate cup under the
0 Press and hold the Key for 1 cup of
Caution! Danger of burns from the
frothing aid! Hold the frothing aid only
by the black seal.

Preparing Hot Water

The hot water can be used to pre-heat
cups and for making hot drinks, e.g. tea
or instant soups.
Caution! Danger of scalding when the
hot water nozzle is activated! Hot
water or steam output can cause
scalding. Activate the hot water nozzle
only when a container is under the hot
water nozzle.
nozzle. Set the Selection dial for steam
and hot water (Fig. 1, D) to the
position (Fig. 19). Hot water is now
prepared.
turn the Selection dial for steam and
hot water (Fig. 1, D) back to the
tion (Fig. 19) and remove the container.
Changing and Saving the
Cup Measure
The coffee machine is factory-set to
standard measures. These measures can
be individually changed to your own
taste and saved for each cup size. The
adjustment can take place in both
bean and powder mode. The setting of
"Cup Measure" is only possible for
1 cup. When dispensing 2 cups the
"Cup Measure" is doubled.
(Fig. 3, d) until the cup symbol, for
which you wish to change the measure,
is illuminated.
coffee dispenser (e.g. coffee mug).
coffee (Fig. 3, b) until the cup/mug
is filled to the desired measure. Release
the key. Your new cup measure is now
saved.
g
posi-
37