Table Of Contents; Meaning Of Symbols; General Safety Advice - GDO 500S/L Einbau- Und Bedienungsanleitung

1.

Table of contents

1. Table of contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2. Meaning of symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3. General safety advice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4. Product overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5. Preparation for mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
6. Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
7. Initial operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
8. Extended operator functions . . . . . . . . . . . . . . . . . . . . . . . . 11
9. Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
10. Malfunctions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
11. Attachment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Reference:
i
The manual comprises a written section and an illustrated section.
The illustrated section is in the centre of the manual on pages 36
and 37.
2.

Meaning of symbols

Caution!
Danger of personal injury!
The following safetly advice must be observed at all times so as to
avoid personal injury!
Attention!
Danger of material damage!
The following safetly advice must be observed at all times so as to
avoid personal injury!
Advice / Tip
Check
i
Reference
3.

General safety advice

Please read carefully!
Target group
This operator system may only be installed, connected and put into
operation by qualified and trained professionals!
Qualified and trained specialist personnel are persons
- who have knowledge of the general and special safety regulations,
- who have knowledge of the relevant electro-technical regulations,
- with training in the use and maintenance of suitable safety equipment,
- who are sufficiently trained and supervised by qualified electricians,
- who are able to recognise the particular hazards involved when working
with electricity,
- with knowledge regarding applications of the EN 12635 standard
(installation and usage requirements).
Warranty
For an operations and safety warranty, the advice in this instruction
manual has to be observed. Disregarding these warnings may lead
to personal injury or material damage. If this advice is disregarded, the
manufacturer will not be liable for damages that might occur.
Batteries, rechargeable batteries, fuses and bulbs are excluded from
warranty.
To avoid installation errors and damage to the door and operator system,
it is imperative that the installation instructions are followed. The system
may only be used after thoroughly reading the respective mounting and
installation instructions.
The installation and operating instructions are to be given to the door
system user, who must keep them safe.
They contain important advice for operation, checks and maintenance.
8
This item is produced according to the directives and standards mentioned
in the Manufacturer's Declaration and in the Declaration of Conformity.
The product has left the factory in perfect condition with regard to safety.
Power-operated windows, doors and gates must be checked by an expert
(and this must be documented) before they are put into operation and
thereafter as required, but at least once a year.
Correct use
The drive system is designed exclusively for opening and closing up-and-
over garage doors and sectional garage doors.
The operator must be used in a dry place.
The maximum push and pull force must be observed.
Door requirements
The door must:
- stand still alone (by balance of springs),
- run smoothly.
Beside the information in this manual, you must also take into
account the information in the door system installation manual
and current general accident prevention and safety regulations!
Our sales and supply terms and conditions are effective.
Information on installing the operator system
• Ensure that the door is in good mechanical condition.
• Ensure that the door can stop in any position.
• Ensure that the door can be easily moved in the OPEN and CLOSE
directions.
• Ensure that the door opens and closes properly.
• Remove all unnecessary components from the door (e.g. cables, chains,
brackets).
• Render any installations inoperable that will no longer be needed after
the operator system has been installed.
• Before commencing cabling works it is very important to disconnect the
operator system from the electricity supply.
Ensure that the electricity supply remains disconnected throughout the
cabling works.
• Adhere to the local protection regulations.
• Lay the electricity supply cables and control cables; these MUST be laid
separately. The controls voltage is 24 V DC.
• Install the operator system with the door in the CLOSED position.
• Install all the impulse transmitters and control devices (e.g. remote
control buttons) within sight of the door and at a safe distance from the
moving parts of the door. A minimum installation height of 1.5 m must
be observed.
• Permanently fix the warning signs, which advise of the danger of
becoming trapped, at conspicuous locations.
• Ensure that no part of the door extends across public footways or roads
when the installation is complete.
Information on commissioning the operator system
After initial operation, the persons responsible for operating the door
system, or their representatives must be familiarised with the use of the
system.
• Make sure that children cannot access the door control unit.
• Before moving the door, make sure that there are neither persons nor
objects in the operating range of the door.
• Test all existing emergency command devices.
• Never insert your hands into a running door or moving parts.
• Pay attention to any parts of the door system that could cause crushing
or shearing damage or accidents.
The EN 13241-1 regulations must be observed.
Information on servicing the operator system
To ensure proper operation, the following items must be checked
regularly and repaired if necessary.
Before any works to the door system are undertaken, the operator system
must be disconnected from the mains.
• Check once a month to ensure that the operator system reverses
if the door encounters an obstacle.
Depending on the operational direction of the door, place a
50 mm high/wide obstacle in its path.
• Check the settings of the OPEN and CLOSE automatic cut-out function.
• Check all movable parts of the door and operator system.
• Check the door system for signs of wear or damage.
• Check whether the door can be easily moved by hand.
Information on cleaning the operator system
Never use water jets, high pressure cleaners, acids or bases for cleaning.
GDO 500S/L - 700S/L (#91376)