Technical Data; Declaration Of Conformity; Auxiliary Handle - Bosch PBH 2800 RE Betriebsanleitung

Technical Data

Rotary Hammer PBH ...
Article number
Speed control
Stop rotation
Right/left rotation
Quick change chuck
Delivery Scope
– Keyless drill chuck
Rated power input
Impact frequency at rated speed
Impact energy per stroke according to
EPTA-Procedure 05/2009
Rated speed
No-load speed
– 1st gear
– 2nd gear
Tool holder
Spindle collar diameter
Drilling diameter, max.:
– Concrete
– Brickwork (with core bit)
– Steel
– Wood
Weight according to
EPTA-Procedure 01/2003
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.

Declaration of Conformity

We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with the fol-
lowing standards or standardization documents: EN 60745
according to the provisions of the directives 2011/65/EU,
2004/108/EC, 2006/42/EC.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
D-70745 Leinfelden-Echterdingen
Henk Becker
Executive Vice President
Engineering
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Leinfelden, 16.04.2014
Bosch Power Tools
2800 RE
3 603 C93 0.. 3 603 C93 1.. 3 603 C93 1.. 3 603 C93 2.. 3 603 C94 2..
W
-1
min
J
-1
min
-1
min 0–1450
-1
min
SDS-plus
mm
mm
mm
mm
mm
kg
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
2900 RE
 
 
 
– –
– –
720 730
4000 4000
2.6 2.7
1100 1100
0–1450
– –
SDS-plus
43 43
26 26
68 68
13 13
30 30
3.0 3.0
/ II / II
Assembly
 Before any work on the machine itself, pull the mains
plug.

Auxiliary Handle

 Operate your machine only with the auxiliary handle 17.
Changing the position of the auxiliary handle
(see figure A)
The auxiliary handle 17 can be set to any position for a secure
and low-fatigue working posture.
– Turn the wing bolt for adjustment of the auxiliary handle 16
in anticlockwise direction and set the auxiliary handle 17
to the required position. Then tighten the wing bolt 16
again in clockwise direction.
Adjusting the Drilling Depth (see figure B)
The required drilling depth X can be set with the depth stop 18.
– Press the button for the depth stop adjustment 15 and in-
sert the depth stop into the auxiliary handle 17.
The knurled surface of the depth stop 18 must face down-
ward.
– Insert the SDS-plus drilling tool to the stop into the SDS-plus
tool holder 3. Otherwise, the movability of the SDS-plus drill-
ing tool can lead to incorrect adjustment of the drilling depth.
2900 FRE 3000 FRE Set
 
 
 
– –
 
730 750
4000 4000
2.7 2.8
1100 1100
0–1450 0–1450
– –
SDS-plus SDS-plus
43 43
26 26
68 68
13 13
30 30
3.0 3.0
/ II / II
1 609 92A 0PJ | (15.4.14)
English | 17
3000-2 FRE





750
4000
2.8
1100
0–1450
0–3000
SDS-plus
43
26
68
13
30
3.3
/ II