Specifications; Additional Safety Rules - Makita 5704R Betriebsanleitung

ENGLISH
1 To avoid kickback, do support
board or panel near the cut.
2 Don't support board or panel
away from the cut.
3 A typical illustration of proper
hand support and workpiece
support.
4 Hex wrench
5 Shaft lock
6 Tighten

SPECIFICATIONS

Model
Blade diameter ............................................. 190 mm
Max. cutting depth
At 90° ......................................................... 66 mm
At 45° .......................................................... 46 mm
-1
No load speed (min ) ...................................... 4,900
Overall length ............................................... 345 mm
Net weight ....................................................... 4.6 kg
• Due to our continuing program of research and
development, the specifications herein are subject
to change without notice.
• Note: Specifications may differ from country to
country.
Power supply
The tool should be connected only to a power supply
of the same voltage as indicated on the nameplate,
and can only be operated on single-phase AC supply.
They are double-insulated in accordance with Euro-
pean Standard and can, therefore, also be used from
sockets without earth wire.
Safety hints
For your own safety, please refer to the enclosed
safety instructions.

ADDITIONAL SAFETY RULES

1. Wear hearing protection.
2. Keep Guards In Place and In Working Order.
Never wedge or tie lower guard open. Check
operation of lower guard before each use.
Don't use if lower guard does not close briskly
over saw blade.
CAUTION: If saw is dropped, lower guard may
be bent, restricting full return.
3. Do not use blades which are deformed or
cracked.
4. Do not use blades of high speed steel.
5. Do not stop the blades by lateral pressure on
the saw blade.
6. Keep Blades Clean and Sharp.
Sharp blades minimize stalling and kickback.
Explanation of general view
7 Loosen
8 Saw blade
9 Outer flange
10 Inner flange
11 Hex socket head bolt
12 Setting protuberances
13 Hex socket head bolt
(For adjusting riving knife)
14 Cutting depth
15 Lever
7. DANGER:
5704R
8. Support Large Panels. (Fig. 1 & 2)
9. Use Rip Fence.
10. Guard Against Kickback. (Fig. 1 & 3)
ENB036-2
11. Lower Guard.
12. Adjustments.
13. Use Only Correct Blades In Mounting.
14. Avoid Cutting Nails.
16 Thumb screw
17 For 45° bevel cuts
18 For straight cuts
19 Base plate
20 Lock-off button
21 Switch trigger
22 Vacuum cleaner
23 Limit mark
24 Brush holder cap
25 Screwdriver
Keep Hands Away From Cutting Area.
Keep hands away from blades. Don't reach
underneath work while blade is rotating. Don't
attempt to remove cut material when blade is
moving.
CAUTION: Blades coast after turn off.
Large panels must be supported as shown in
Fig. 1 to minimize the risk of blade pinching
and kickback.
When cutting operation requires the resting of
the saw on the workpiece, the saw shall be
rested on the larger portion and the smaller
piece cut off.
Always use a fence or straight edge guide
when ripping.
Kickback occurs when the saw stalls rapidly
and is driven back towards the operator.
Release switch immediately if blade binds or
saw stalls. Keep blades sharp. Support large
panels as shown in Fig. 1.
Use fence or straight edge guide when ripping.
Don't force tool. Stay alert – exercise control.
Don't remove saw from work during a cut
while the blade is moving.
NEVER place your hand or fingers behind the
saw. If kickback occurs, the saw could easily
jump backwards over your hand, possibly
causing severe injury.
Raise lower guard with the retracting handle.
Before cutting be sure depth and bevel adjust-
ments are tight.
Don't use blades with incorrect size holes.
Never use defective or incorrect blade wash-
ers or bolts.
Inspect for and remove all nails from lumber
before cutting.
5