Accessories; Optional Parts; Installation Work; Selecting An Installation Location - AirStage ABYA12GATH Installationsanleitung

] 1

2.3. Accessories

For installation purposes, be sure to use the parts supplied by the manufacturer or
other prescribed parts. The use of non-prescribed parts can cause serious accidents
such as the unit falling, water leakage, electric shock, or fi re.
The following installation parts are furnished. Use them as required.
Keep the Installation Manual in a safe place and do not discard any other accessories
until the installation work has been completed.
Name and Shape
Operating Manual
Installation Manual
Cover plate (Left)
Cover plate (Right)
Tapping screw
(M4 × 10mm)
Installation template
Bracket (Left)
Bracket (Right)
Special nut
Wall bracket
Tapping screw
(M4 × 20mm)
Coupler heat insulation
Cable tie (Large)
Cable tie (Medium)
9367701100-01_IM.indb Sec1:2 9367701100-01_IM.indb Sec1:2
WARNING
Q'ty Application
1
(This book)
1
1
1
2
For positioning the indoor unit
For under ceiling type
1
For suspending the indoor unit from
ceiling
1
1
4
For suspending the indoor unit on the
wall
2
For fi xing the wall bracket
6
For indoor side pipe joint
2
For fi xing the coupler heat insulation
4
For power supply, transmission and
remote controller cable binding
2
Name and Shape Q'ty
Drain hose
Hose Band
Drain hose insulation
VT wire
Insulation (Pipe)
Silencer pipe
] 1

2.4. Optional parts

Description Part No.
Auxiliary pipe
9374714025
External output wire 9379529013
External input wire D 9368779016
External input wire F 9368779023
External input wire B 9368778002
External input wire E 9368778019

3. INSTALLATION WORK

Correct initial installation location is important because it is diffi cult to move unit after it is
installed.
] 1

3.1. Selecting an installation location

Decide the mounting position together with the customer as follows.
WARNING
Select installation locations that can properly support the weight of the indoor unit.
Install the units securely so that they do not topple or fall.
CAUTION
Do not install the indoor unit in the following areas:
• Area with high salt content, such as at the seaside. It will deteriorate metal parts,
causing the parts to fail or the unit to leak water.
• Area fi lled with mineral oil or containing a large amount of splashed oil or steam,
such as a kitchen. It will deteriorate plastic parts, causing the parts to fail or the unit
to leak water.
• Area that generates substances that adversely affect the equipment, such as
sulfuric gas, chlorine gas, acid, or alkali. It will cause the copper pipes and brazed
joints to corrode, which can cause refrigerant leakage.
• Area that can cause combustible gas to leak, contains suspended carbon fi bers or
fl ammable dust, or volatile infl ammables such as paint thinner or gasoline. If gas
leaks and settles around the unit, it can cause a fi re.
• Area where animals may urinate on the unit or ammonia may be generated.
Do not use the unit for special purposes, such as storing food, raising animals,
growing plants, or preserving precision devices or art objects.
It can degrade the quality of the preserved or stored objects.
Do not install where there is the danger of combustible gas leakage.
Do not install the unit near a source of heat, steam, or fl ammable gas.
Install the unit where drainage does not cause any trouble.
Application
For installing drain pipe
VP25 (O.D.32, I.D.25)
1
For installing drain hose
1
Adhesive type
(100 × 220 mm)
1
For fi xing the drain hose L 280 mm
1
Adhesive type
(160 × 110 mm)
1
Connect the silencer pipe to the small
(liquid) pipe.
1
Application
For indoor side pipe joint
(For AB18, AB24)
For output port
For control input port
(Apply voltage terminal)
For control input port
(Dry contact terminal)
For forced thermostat off port
(Apply voltage terminal)
For forced thermostat off port
(Dry contact terminal)
En-2
2012-7-12 14:01:30 2012-7-12 14:01:30