Operation; Maintenance; Optional Accessories - Makita TM3010C Betriebsanleitung

2. Put an application tool (optional accessory) on the
tool flange so that the protrusions of the tool flange
fit in the holes in the application tool.
3. Insert the holder bolt till it stops. And then, return the
lock lever to its original position.
When using sanding application tool, mount the
application tool on the sanding pad so that it matches the
sanding pad direction.
The sanding pad has a hook and loop type fitting system
which allows easy and rapid fitting of a sanding paper.
As sanding papers have holes for dust extraction, mount
a sanding paper so that the holes in a sanding paper
match those in the sanding pad.
To remove a sanding paper, raise its end and peel it off.
To remove the holder bolt, follow the installation
procedures in reverse.
When using application tools with a different type of
installation section, use a correct adapter (optional
accessory).

OPERATION

WARNING:
• Before starting the tool and during operation, keep your
hand and face away from the application tool.
CAUTION:
• Always hold the tool firmly with one hand on housing.
Do not touch the metal part.
• Do not apply excessive load to the tool which may
cause a motor lock and stop the tool.
Cutting, sawing and scraping (Fig. 7)
CAUTION:
• Do not move on the tool forcibly in the direction (e.g.
towards either side) of tool application with no cutting
edge. It may damage the tool.
Put the application tool on the workpiece.
And then move the tool forward so that the application
tool movement does not slow down.
NOTE:
• Forcing or excessive pressure on the tool may reduce
efficiency.
• Remove sawdust by drawing tool adequately. It
increases work efficiency.
• Before cutting operation, it is recommended to preset
the orbital stroke rate 3 – 5.
• The round saw is recommended for cutting long
straight line.
Sanding (Fig. 8)
CAUTION:
• Do not reuse a sanding paper used for sanding metal
to sand wood.
• Do not use a worn sanding paper or sanding paper
without grit.
Apply a sanding paper on the workpiece.
NOTE:
• Using a test material sample to try is recommendable
to determine a correct orbital stroke rate suitable for
your work.
• Use a sanding paper with the same grit until sanding
the whole workpiece is completed. Replacing a
sanding paper with different grit sanding paper may not
get a fine finish.
Dust extraction attachment (optional accessory)
(Fig. 9, 10 & 11)
• Install joint, dust nozzle and dust attachment.
• Install the nozzle band on the tool so that its
protrusions fit in the holes in the tool to secure it.
• Put the felt ring and the sanding pad on the dust
attachment and then secure them with the application
tool installation bolt.
When you wish to perform cleaner operation, connect a
vacuum cleaner to your tool. Connect a hose of vacuum
cleaner to the dust extraction attachment (optional
accessory).

MAINTENANCE

CAUTION:
• Always be sure that the tool is switched off and
unplugged before attempting to perform inspection or
maintenance.
• Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
To maintain product SAFETY and RELIABILITY, repairs,
carbon brush inspection and replacement, any other
maintenance or adjustment should be performed by
Makita Authorized Service Centers, always using Makita
replacement parts.

OPTIONAL ACCESSORIES

CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• Segment saw blade
• Round saw blade
• Plunge cut saw blade
• Scraper (rigid)
• Scraper (flexible)
• Serrated seg blade
• General joint cutter
• HM remover
• HM seg saw blade
• HM sanding plate
• Diamond seg sawblade
• Sanding pad
• Adapter
• Abrasive paper delta (red / white / black)
• Fleece delta (medium / coarse / without grit)
• Polishing felt delta
• Hex wrench
• Dust extraction attachment
NOTE:
• Some items in the list may be included in the tool
package as standard accessories. They may differ from
country to country.
7