Specifications - Makita TM3010C Betriebsanleitung

ENGLISH
(Original instructions)
1 Slide switch
2 Dial
3 Holder bolt
4 Lock lever
5 Holes in the application tool

SPECIFICATIONS

Oscillation per minute
Oscillation angle, left/right
Overall length
Safety class
• Due to our continuing program of research and
development, the specifications herein are subject to
change without notice.
• Specifications may differ from country to country.
• The weight may differ depending on the attachment(s).
The lightest and heaviest combination, according to
EPTA-Procedure 01/2014, are shown in the table.
Intended use
The tool is intended for sawing and cutting wood, plastic,
gypsum, non-ferrous metals, and fastening elements (e.
g. unhardened nails and staples). It is also intended for
working soft wall tiles, as well as dry sanding and
scraping of small surfaces. It is especially for working
close to edge and flush cutting.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
General power tool safety warnings
WARNING: Read
instructions, illustrations
provided with this power tool. Failure to follow all
instructions listed below may result in electric shock, fire
and/or serious injury.
Save all warnings and instructions for future
reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Explanation of general view
6 Protrusions of the tool flange
7 Adapter
8 Joint
9 Nozzle band
10 Dust nozzle
Model
Net weight
all safety warnings,
and specifications
MULTI TOOL SAFETY WARNINGS
1. This power tool is intended to function for
sawing, cutting, grinding and sanding. Read all
safety warnings, instructions, illustrations and
specifications provided with this power tool.
Failure to follow all instructions listed below may
ENE080-1
result in electric shock, fire and/or serious injury.
2. Hold the power tool by insulated gripping
surfaces, when performing an operation where
the cutting accessory may contact hidden wiring
or its own cord. Cutting accessory contacting a
"live" wire may make exposed metal parts of the
power tool "live" and could give the operator an
electric shock.
3. Use clamps or another practical way to secure
ENF002-2
and support the workpiece to a stable platform.
Holding the work by hand or against your body
leaves it unstable and may lead to loss of control.
4. Position
accessory. If you lose control, the cord may be cut
or snagged and your hand or arm may be pulled into
the spinning accessory.
5. Always use safety glasses or goggles. Ordinary
GEA010-2
eye or sun glasses are NOT safety glasses.
6. Avoid cutting nails. Inspect workpiece for any
nails and remove them before operation.
7. Hold the tool firmly.
8. Make sure the application tool is not contacting
the workpiece before the switch is turned on.
9. Keep hands away from moving parts.
10. Do not leave the tool running. Operate the tool
only when hand-held.
11. Always switch off and wait for the blade to come
to a complete stop before removing the blade
from the workpiece.
12. Do not touch the application tool or the
workpiece immediately after operation; they may
be extremely hot and could burn your skin.
13. Do not operate the tool at no-load unnecessarily.
14. Always use the correct dust mask/respirator for
the material and application you are working
with.
11 Dust attachment
12 Felt ring
13 Pad
14 Protrusions
15 Holes
TM3010C
–1
6,000 – 20,000 (min )
1.6° (3.2° total)
283 mm
1.6 kg – 1.7 kg
/II
the cord clear of
GEB142-1
the spinning
5