Operation - Makita DTWA070 Betriebsanleitung

Alarm No.
- Alarm for no com-
munication with
the PC
- Indication that the
tool can communi-
cate with the PC
- Check for the lamp
and beeper (when
the battery cartridge
is installed)
ASSEMBLY
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Selecting correct impact socket
Always use the correct size impact socket for bolts and
nuts. An incorrect size impact socket will result in inac-
curate and inconsistent fastening torque and/or damage
to the bolt or nut.
Installing or removing impact socket
Optional accessory
CAUTION:
Make sure that the impact socket
and the mounting portion are not damaged before
installing the impact socket.
CAUTION:
After inserting the impact socket,
make sure that it is firmly secured. If it comes out,
do not use it.
NOTE: The way of impact socket installation varies
depending on the type of the square drive on the tool.
Tool with the ring spring
For impact socket without O-ring and pin
► Fig.13: 1. Impact socket 2. Square drive 3. Ring spring
Push the impact socket onto the square drive until it
locks into place.
To remove the impact socket, simply pull it off.
For impact socket with O-ring and pin
► Fig.14: 1. Impact socket 2. O-ring 3. Pin
Move the O-ring out of the groove in the impact socket
and remove the pin from the impact socket. Fit the impact
socket onto the square drive so that the hole in the impact
socket is aligned with the hole in the square drive.
Insert the pin through the hole in the impact socket and
square drive. Then return the O-ring to the original posi-
tion in the impact socket groove to retain the pin.
To remove the impact socket, follow the installation
procedures in reverse.
Function Status of the tool
No data commu-
nication while the
tool is connected to
the PC.
The tool is connected
to the PC and able to
communicate with.
The tool performs
the operation test
for the LED indicator
(green/red), light,
and beeper.
Status of the LED indicator/beeper
LED indicator
Blinks in yellow.
Blinks in green.
The LED indicator
lights up in green
and then red. After
that, the light turns
on for a while.
Tool with the detent pin
► Fig.15: 1. Impact socket 2. Hole 3. Square drive
4. Detent pin
Align the hole in the side of the impact socket with the
detent pin on the square drive and push the impact
socket onto the square drive until it locks into place. Tap
it lightly if required.
To remove the impact socket, simply pull it off. If it is
hard to remove, depress the detent pin while pulling the
impact socket.
Installing hook
Optional accessory
The hook is useful to hang the tool. Install the hook to
the holes on the tool body.
► Fig.16: 1. Hook 2. Hole

OPERATION

CAUTION:
Always insert the battery cartridge
all the way until it locks in place. If you can see the
red indicator on the upper side of the button, it is not
locked completely. Insert it fully until the red indicator
cannot be seen. If not, it may accidentally fall out of
the tool, causing injury to you or someone around
you.
CAUTION:
Hold the tool firmly and place the
impact socket over the bolt or nut. Turn the tool on
and fasten for the proper fastening time.
CAUTION:
If the tool is operated continuously
until the battery cartridge has discharged, allow the
tool to rest for 15 minutes before proceeding with a
fresh battery cartridge.
CAUTION:
Pressing excessively on the tool
will not speed up the drilling. In fact, this excessive
pressure will only serve to damage the tip of your drill
bit, decrease the tool performance and shorten the
service life of the tool.
CAUTION:
Always secure workpieces in a
vise or similar hold-down device.
12 ENGLISH
Action to be taken
Beeper
– Restart the appli-
cation software and
re-connect the USB
cable.
–
A series of very
short beeps
–
–