Chicco Journey Gebrauchsanleitung Seite 14

Chicco Journey Table Seat
GB
READ THE INSTRUCTIONS CAREFULLY BEFORE USE AND
KEEP THEM FOR FUTURE REFERENCE. YOUR CHILD MAY BE
HURT IF YOU DO NOT FOLLOW THE INSTRUCTIONS.
WARNINGS
• WARNING: never leave your child unattended in this
table mounted chair
• WARNING: keep coverings away from children to avoid
suffocation
• WARNING: The width of the table top to which the
table seat can be fastened must measure: minimum 19 mm
and maximum 38 mm.
• WARNING: Check that the table will not tip when the
table mounted chair, attached to it, is in use.
• WARNING: The table mounted chair is not suitable for
children who cannot sit unaided
• WARNING: Designed for use for children from 6
months. The table mounted chair shall not be used by
children weighing more than 15 kg
• WARNING: Do not use on glass topped tables, tables
with loose table-tops, table leaves, single pedestal tables,
card tables or camping tables
• WARNING: Do not attach the table mounted chair
where the child might use its feet to push agaist a part
of the table, another chair or any other structure as this
could cause the table mounted chair to come off the table.
• WARNING: Do not use tablecloths or other objects on
the support surface which might interfere with the proper
functioning of the anchoring elements. Keep the table
structure and surface clean and dry
• WARNING: Do not use the table mounted chair if any
components are broken or missing.
• WARNING: Do not use replacement parts other than
those approved by manufacturer or distributor.
• WARNING: Routinely check any clamping screws and
retighten them, if required. Also check that the non-slip
pads are in good condition and work efficiently.
• Do not hang any objects on the table seat that could
unbalance it
• Do not fasten or remove the table seat with the child
sitting inside it.
• Do not use the table seat for more than one child at a
time.
• Do not allow other children to play unsupervised near
the table seat.
• When not in use, keep the table seat out of reach of children.
CHICCO JOURNEY COMPONENTS
A. Tubular table seat with fabric cover
B. 2 table seat connector arms
C. Connector pin release buttons
D. Connector pins
E. Pin tightener knob
F. Restraint belt with double safety buckle
G. Backrest support
H. Seat base support
I. Item holder pocket
J. Bag holder pocket
K. Travel carrying bag
ASSEMBLY
1. Insert the backrest support (G) in the vertical pocket
positioned under the bottom of the table seat backrest (Diag.
1). Insert the backrest support making sure that the curved part
is facing upwards and slide the backrest support inside the table
seat, with the tubular frame on the outside so it does not come
into contact with the child's back. When the support frame has
been fitted, close the pocket using the velcro fastener so the
rigid backrest cannot slide out when in use (Diag. 2).
2. Attach the two connector arms (B) to the table seat tubular
frame (A). Now proceed as follows: Insert the arm aligning the
red symbol located on the product seat with the red symbol
located on the table seat tubular frame (Diag. 3A/3B).
The arm is fitted correctly when you hear both the locking
buttons (Diag. 4) click into place. Repeat this procedure for the
other arm. Check that the arms are fastened properly.
3. Fit the two fabric cover flaps around the arm frame and
fasten in place using the snap-buttons (Diag. 5).
USER INSTRUCTIONS
4. Press the lower connector pins release buttons (C ) and push
the pins downwards (diagram 6).
5. Tilt the table seat, lifting the rear section, and position it on
the table top (diagram 7). Push it as far as possible (Diag. 8).
6. Push the connector pin upwards (D) until it comes into
contact with the lower surface of the table top (diagram
9A/9B); repeat the procedure on the other side.
7. Finish regulating the seat turning the knobs (E), located under
the pins, COUNTER CLOCKWISE, until the product is firmly
fastened in place (Diag. 10). Push the table seat outwards to
test its stability: it must not move away from the tale top.
8. Undo the double safety buckle (F) (Diagram 11) to open
the harness strap and sit your child inside. Do not place chairs
or similar objects under the table seat when in use. Always
remove your child from the table seat before disconnecting it
from the table top.
9. To disconnect the table seat from the table top, turn both
the knobs CLOCKWISE until they reach their original position.
Now press the connector pins release buttons (C ) and the pins
will automatically unlock, sliding downwards.
REMOVABLE COVERS
10. Undo the two fabric cover snap-buttons (diagram 12).
11. Press the two locking buttons to remove the arms (diagram
13A/13B).
12. Thread the harness strap (F) through the slots on the fabric
cover (diagram 17A/17B).
13. Remove the backrest support (G) from the pocket (diagram
14); now slide the tubular frame outwards to remove it from
the fabric cover (diagram 15).
14. Open the snap-button in the middle of the seat and slide
out the seat base frame (H) (diagram 16A/16B).
15. Repeat the procedure in the reverse order to fit the fabric
cover, making sure the harness strap is threaded correctly
though the relative slots (diagram 17A/17B).
14
WASHING