Technical Data; Before First Use - Scheppach Ms40-42Li Originalbetriebsanleitung

• The battery voltage must correspond with the
battery charging voltage of the charger. Oth-
erwise, there is a risk of fire and explosion.
• Charge the batteries only in chargers that have
been recommended by the manufacturer. There
is a risk of fire if a charger for a particular type of
battery is used for another type of battery.
• The battery can be damaged by sharp objects
such as a nail or screwdriver or by external ap-
plication of force. The battery may short-circuit
and start burning, smoking, exploding or overheat-
ing.
Warning! This electric tool generates an electro-
magnetic field during operation. This field can impair
active or passive medical implants under certain
conditions. In order to prevent the risk of serious or
deadly injuries, we recommend that persons with
medical implants consult with their physician and the
manufacturer of the medical implant prior to operat-
ing the electric tool.
Remaining hazards
The machine has been built using modern technology
and in accordance with recognized safety rules.
Some hazards, however, may still remain.
• There is a risk of injury from rotating parts.
• There is a danger from items being ejected.
• Wear regulation safety gear such as safety boots
and tight work clothing.
• Electrical hazards exist when unsuitable electric
connections are used.
• Although having regarded all considerable rules
there may still remain not obvious remaining haz-
rds.
• Minimize remaining hazards by following the in-
structions in "Safety Rules", "Use only as author-
ized" and in the entire operating manual.

6. Technical data

Nominal voltage
Type of battery
Cutting width
Cutting height
Grass box capacity
Idle speed
Weight (with battery)
Noise and vibration
The noise and vibration values were developed us-
ing a standardised measuring process.
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
Sound pressure L
Sound power L
Sound power L
Uncertainty K
Vibration a
Uncertainty K
Wear ear-muffs.
The impact of noise can cause damage to
Reduce noise generation and vibration to a minimum!
• Use only equipment that is in perfect condition.
• Maintain and clean the equipment regularly.
• Adopt your way of working to the equipment.
• Do not overload the equipment.
• Have the equipment checked if necessary.
• Switch off the equipment when not in use.
• Wear gloves
7. Assembly
1. Take the mower and attachment parts out of the
2. Attach the lower push bar to both sides of the
3. Attach the upper push bar on the lower push bar
4. Fix the cables to the push bar with the cable clips
5. Grass box (4) - open it up and click the plastic
6. Mowing with grass box:
40 V
7. Mulching:
4,0 Ah
42 cm
25 - 70 mm
40 l
Mounting the grass box (Fig. 9)
3000 1/min
• Flip open the discharge flap (9).
22 kg
• Mount the grass box (4) on the lawn mower.
Battery assembly (Fig. 19)
Open the battery compartment lid (7). Then insert
the battery into the holder as shown.
Note:
Only ever use batteries with the same level of charge.
Do not combine full and half full batteries. Always
charge both batteries at the same time.
pA
(measured)
wA
(guaranteed)
wA
WA
h
packaging and check that all parts are present.
mower with two screws (a, e), 2 washer (b), one
plastic grip nut (c) and one star grip nut (d) each.
Make sure that the cables, which will be attached
later, are not in the way (Fig. 2-3).
with one quick-release lever (5), one fixation slice
(g), one washer (b) and one plastic nut (f) each on
both sides (Fig. 4-5). Note the correct alignment
of the quick-release lever fixation slice ensuring
the quick-release function remains intact.
(10) provided (Fig. 7).
clips into position on the frame (Fig. 8).
Lift the discharge flap (9) with one hand and hang
the grass box (4) as shown in Fig. 9.
If the grass box (4) is attached, remove it and re-
place it with the mulch insert (11) as shown in Fig.
10-12.
79,5 dB(A)
93,47 dB(A)
96 dB(A)
3 dB(A)
1,98 m/s²
0,5 m/s²
hearing..
GB 23