Maintenance And Service; Maintenance And Cleaning; After-Sales Service And Application Service - Bosch ANGLE EXACT 2 Originalbetriebsanleitung

OBJ_BUCH-412-002.book Page 27 Monday, December 9, 2013 5:34 PM
2 | 3 | 6 | 7 | 7–900 | 8 |
ANGLE EXACT
10–650 | 14–420 | 14CF | 15 |
17 | 22CF | 23 | 25–200 | 29CF
30 | 30–300
Press off the marking ring 17 with a thin screwdriver blade, a
knife, or similar.
Using snap-ring pliers, slide the snap ring 34 toward the rear
onto the housing shell.
The two shell halves of the LED holder 16, which enclose the
LED worklight 18, can now be adjusted to any requested po-
sition. Pay attention not to damage the cable of the LED work-
light 35 and slide it into the cavity intended for it in the hous-
ing shell without kinking. Enclose the LED worklight 18 again
with the two housing shells of the LED holder 16.
Press the snap ring 34 and the marking ring 17 back to their
initial positions.

Maintenance and Service

Maintenance and Cleaning

 Before any work on the machine (e. g., maintenance,
tool change, etc.) as well as during transport and stor-
age, set the rotational direction switch to the centre
position. Unintentional actuation of the On/Off switch can
lead to injuries.
 For safe and proper working, always keep the machine
and ventilation slots clean.
When the battery is no longer operative, please refer to an au-
thorised after-sales service agent for Bosch power tools.
Power Tool Lubrication
Lubricants:
Special gearbox grease (225 ml)
Article number 3 605 430 009
Molycote grease
SAE 10/SAE 20 engine oil
Clean the gearbox after the first 150 running hours using a
mild solvent. Follow the solvent manufacturers directions for
use and disposal. Lubricate the gearbox using Bosch gearbox
lube. Repeat the lubrication procedure every 300 hours after
the initial gearbox service.
Oil the moving parts of the shut-off clutch after 100000
screwing operations with a few drops of SAE 10/SAE 20 mo-
tor oil. Lubricate the sliding and rolling parts with Molycote
grease. At this time, inspect the clutch for wear in order to en-
sure that the repeatability and accuracy have not been affect-
ed. Afterwards, the torque of the clutch must be readjusted.
 Have maintenance and repair work performed only by
qualified specialists. In this manner, it can be ensured
that the safety of the power tool is maintained.
An authorized Bosch after-sales service agent will carry out
this work quickly and reliably.
Observe all applicable environmental regulations when
disposing of old grease and solvents.
Bosch Power Tools

After-sales Service and Application Service

Robert Bosch GmbH is responsible for the delivery of this
product in accordance with the sales contract within the
framework of the legal/country-specific regulations. For
claims with respect to the product, please contact the follow-
ing location:
Fax: +49 (711) 7 58 24 36
www.boschproductiontools.com
In all correspondence and spare parts order, please always in-
clude the 10-digit article number given on the type plate of
the machine.
Disposal
The machine, accessories and packaging should be sorted for
environmental-friendly recycling.
According to the European Directive
2012/19/EU for Waste Electrical and Elec-
tronic Equipment and its implementation
into national right, power tools that are no
longer usable must be collected separately
and disposed of in an environmentally cor-
rect manner.
Battery packs/batteries:
Ni-Cd: Nickel cadmium
Warning: These battery packs contain cadmium, a highly toxic
heavy metal.
Ni-MH: Nickel metal hydride
Do not dispose of battery packs/batteries into household
waste, fire or water. Battery packs/batteries should, if possi-
ble, be discharged, collected, recycled or disposed of in an
environmental-friendly manner.
Only for EC countries:
Defective or dead out battery packs/batteries must be recy-
cled according the guideline 2006/66/EC.
Batteries no longer suitable for use can be directly returned
at:
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange
the collection of a product in need of servicing or repair.
Tel. Service: (0844) 7360109
E-Mail: boschservicecentre@bosch.com
Subject to change without notice.
English | 27
3 609 929 C62 | (9.12.13)