Maintenance And Service; Maintenance And Cleaning; After-Sales Service And Application Service - Bosch GDS 12V-115 Professional Originalbetriebsanleitung

For a spring-loaded seat as well as for a soft seat, the max-
imum tightening torque is lower than for a hard seat. Also, a
clearly longer impact duration is required.
Guide values for maximum screw tightening torques
Figures given in Nm; calculated from the tensional cross-section; utilization of the yield point: 90% (with friction coefficient
µ = 0.12). As a control measure, always check the tightening torque with a torque wrench.
total
Property Classes Standard Screws/Bolts
according to
3.6 4.6
DIN 267
M6 2.71 3.61
M8 6.57 8.7
M10 13 17.5
M12 22.6 30
M14 36 48
M16 55 73
Tips
Before screwing larger, longer screws into hard materials, it
is advisable to pre-drill a pilot hole with the core diameter of
the thread to approx. 2/3 of the screw length.
Note: Ensure that no metal particles enter the power tool.
Recommendations for optimal handling of the battery
Protect the battery against moisture and water.
Only store the battery within a temperature range of -20 to
50 °C. Do not leave the battery in your car in the summer, for
example.
A significantly reduced operating time after charging indic-
ates that the battery has deteriorated and must be replaced.
Follow the instructions on correct disposal.
Occasionally clean the ventilation slots and the terminals on
the battery using a soft brush that is clean and dry.
Belt clip (see figure E)
You can use the belt clip (17) to hang the power tool on a
belt, for example. You then have both hands free and the
power tool is always at hand.
Coloured clip (see figure F)
You can use the coloured clip (18) to individually identify the
power tool.

Maintenance and Service

Maintenance and Cleaning

Clean the tool holder (1) and locking sleeve (2) from
u
time to time.
Clean the air vents on your power tool regularly. The
u
motor's fan will draw the dust inside the housing and ex-
cessive accumulation of powdered metal may cause elec-
trical hazards.
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Bosch Power Tools
5.6 4.8 6.6 5.8
4.52 4.8 5.42 6.02
11 11.6 13.1 14.6
22 23 26 29
37.6 40 45 50
60 65 72 79
92 98 110 122
To ensure safe and efficient operation, always keep
u
the power tool and the ventilation slots clean.

After-Sales Service and Application Service

Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the nameplate
of the product.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange
the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com
You can find further service addresses at:
www.bosch-pt.com/serviceaddresses
Transport
The contained lithium-ion batteries are subject to the Dan-
gerous Goods Legislation requirements. The batteries are
suitable for road-transport by the user without further re-
strictions.
When shipping by third parties (e.g.: by air transport or for-
warding agency), special requirements on packaging and la-
belling must be observed. For preparation of the item being
shipped, consulting an expert for hazardous material is re-
quired.
High-strength Bolts
6.8 6.9 8.8 10.9
7.22 8.13 9.7 13.6
17.5 19.7 23 33
35 39 47 65
60 67 80 113
95 107 130 180
147 165 196 275
1 609 92A 6PS | (14.09.2021)
English | 17
12.9
16.2
39
78
135
215
330