Troubleshooting - Pioneer MEP-7000 Bedienungsanleitung

TROUBLESHOOTING

TROUBLESHOOTING
If you believe your player is failing to work properly, check the following troubleshooting table for tips. Sometimes simple mistakes in setup
or operation may appear like serious problems. There are also times when the problem in question may be caused by something else other
than your player, and at times like these you should check any other electronic devices being used at the same time.
If the problem in question continues to persist even after checking the troubleshooting table below and taking whatever corrective action
is recommended, contact your nearest Pioneer Service Station or contact the store from which you purchased your player for further
assistance.
Description of problem
A disc fails to be ejected even
after the EJECT () button has
been pressed.
Playback doesn't begin even
when a disc is inserted.
Playback comes to a halt
almost immediately after it
begins.
USB storage device not
detected.
A caution message to the
effect that "an excess current
has been detected" will appear
in the center display.
Can't play MP3 or AAC tracks. • Format not supported.
No sound is output.
Sound is distorted or full of
noise.
64
En
Possible cause of problem
• Power cord has not been plugged in.
• A track is being played back.
• EJECT () button is broken.
• Auto Cue function is turned ON.
• CD-R/RW, DVD ±R/RW or other media are of
poor quality.
• Format not supported.
• Disc has been inserted upside down.
• Disc is dirty or covered with condensation.
• Device does not comply with USB mass storage
class.
• USB hub in use.
• Format not supported.
• The connection with this unit has been
terminated because an electrical current
stronger than that allowable was applied to this
unit's USB1 port or USB2 port.
• Files are copy-protected.
• Audio cable has come loose or has not been
properly plugged in.
• DJ mixer is not working properly.
• Jacks or jack plugs are dirty.
• Controller is currently in pause mode.
• Audio cable has not been properly plugged in.
• Jacks or jack plugs are dirty.
• Player is subject to noise from a nearby
television set.
Recommended action
• Plug in power cord.
• Set the player to pause or cue standby mode
before pressing the EJECT () button.
• See P. 23.
• Press the play/pause () button to begin play.
• Hold the TIME/A.CUE button depressed for one
second or more to set the Auto Cue mode to
OFF.
• Replace with other media, or media recorded on
a different recording machine.
• See P. 10 "REGARDING PLAYABLE DISCS AND
FILES" regarding supported formats.
• Reinsert with label side facing upward.
• Wipe disc to remove dust or condensation.
• Use a device complying with USB mass storage
class (some portable audio players included in
the class of image devices are not supported.
Also, some flash card readers cannot be
detected).
• Some USB hubs will not operate properly. Try a
different USB hub, or connect the storage
device directly to the USB port. Also, if multiple
USB storage devices are connected through a
USB hub, only one of the devices will be
recognized.
• Use only FAT, FAT32, or HFS+ formats.
• Restore normal operation by following the
directions listed in "Connecting a USB storage
device" (P. 25). The rating (allowable current) for
this unit is 500 mA or less per port. Use USB
storage devices that meet these standards. If
you have a USB storage device connected
through a bus-powered USB hub, connect the
USB storage device directly to this unit.
• See P. 10 "REGARDING PLAYABLE DISCS AND
FILES" regarding supported formats.
• Cannot be used on this unit.
• Plug in audio cable properly.
• Check switch and volume settings on DJ mixer.
• Wipe away dust or dirt and reinsert plugs.
• Press the play/pause () button to begin play.
• Connect audio cable to line input jack of DJ
mixer. Do not connect to microphone jack.
• Wipe away dust or dirt and reinsert plugs.
• Turn off power to television set or move
television set further away from player.