Installation Guidelines; Transporting The Unit - Pioneer MEP-7000 Bedienungsanleitung

INSTALLATION GUIDELINES

INSTALLATION GUIDELINES
• Placing and using the player for long periods on heat-generating
sources such as amplifiers or near spotlights, etc. will affect
product performance. Avoid placing the player on heat-
generating sources.
• Install this player as far as possible away from tuners and TV
sets. A player installed in close proximity to such equipment
may cause noise or degradation of the picture. Noise may be
noticeable when an indoor antenna is used. In such cases,
make use of an outdoor antenna or turn off power to the player.
• When the unit is used in a loud-sound environment, e.g., near a
speaker, sound skip may occur. Install the unit away from the
speaker or reduce the listening volume.
• Place this unit on a level surface and a stable platform.
• Do not place heavy objects on top of the unit.
Be sure the player, including its audio and power supply cords,
does not touch vibrating materials. Any cause of vibration other
than the insulators may cause sound skip.
Take special care when using the player while it is installed in a
carrying case.
To assure proper heat-
dissipation, be sure to
maintain this open space.
To assure proper
heat-dissipation, be
sure to maintain this
open space.
Installing the MEP-7000 in an EIA rack
The screw holes on the front panel of the MEP-7000 are designed
for use in attaching the unit to a 19-inch EIA rack.
Control unit complies with 3U specifications; drive unit complies
with 2U. Maximum depth of unit is 324.6 mm.
• Attach the unit to the rack using screws of the appropriate size
(screws not provided with the unit).
NOTE
• Do not install the unit immediately above a power amplifier,
since damage may occur from the heat produced by the
amplifier, or humming or other noise may be caused.
• When transporting the unit, remove the unit from its rack.
Attempting to move the rack with the unit installed may
result in damage to the unit.
• If the unit must be moved while still in its rack, take
precautions to protect the unit from vibration and impact.
14
En
Do not allow contact
with vibrating surfaces.
To assure proper
heat-dissipation, be
sure to maintain this
open space.

Transporting the unit

 Never move the unit during playback.
During playback, discs rotate at very high speeds; never lift or
move the unit during this time to prevent scratches or other
damage to discs.
 Transporting the unit
When moving the unit, always remove any discs that have been
loaded, and turn off the power.
Moving the unit with a disc loaded could result in damage to the
disc or unit.
About carrying cases
The jog dial is equipped with a delicate switch. If the unit is placed
in a carrying case, take precautions to prevent any pressure from
being exerted on the surface of the jog dial.
Condensation
When this unit is brought into a warm room from previously cold
surroundings or when the room temperature rises sharply,
condensation may form inside the unit and impair its
performance. In such cases, allow the unit to stand for about an
hour or raise the room temperature gradually.
Cleaning the player
To clean the player wipe with a polishing or a soft, dry cloth. For
stubborn dirt, moisten a soft cloth with a weak solution of neutral
detergent (diluted in five to six parts water), wring the cloth well,
and wipe away the dirt. Use a dry cloth to wipe the surface dry. Do
not use volatile liquids such as benzene or thinner which will
damage to the unit.
CD lens cleaner
If for some reason, the lens becomes soiled and malfunctions,
contact your nearest PIONEER authorized service center. Lens
cleaners for CD players are commercially available, but special
care should be exercised in their use as some may cause damage
to the lens.
Cleaning the Jog Dial
To clean the jog dial wipe with a polishing or a soft, dry cloth. For
stubborn dirt, moisten a soft cloth with a weak solution of neutral
detergent (diluted in five to six parts water), wring the cloth well,
and wipe away the dirt. Use a dry cloth to wipe the surface dry.
Applying alcohol, paint thinner, benzene, insecticides, or other
stringent substances to the jog dial may cause the markings or
finishing of the dial to peel or become discolored, and the use of
any such substances should accordingly be avoided.