Identification Of The Parts; Assembly; Mounting The Blade And Trimmerhead - Texas A/S BCP 4300 Bedienungsanleitung

Gasoline safety
Use extreme care in handling gasoline. Gasoline is
extremely flammable and the fumes are explosive.
Serious personal injury can occur, when gasoline is
spilled on yourself or your clothes. Rinse your skin
and change clothes immediately!
Use only an approved gasoline container. Do not
use soft drink bottle or similar!
Extinguish all cigarettes, cigars, pipes and other
sources of ignition.
Never refuel your machine indoors.
Let the engine cool down before refilling
Never fill the fuel tank to more than 1 cm below
bottom of filler in order to provide space for fuel to
expansion.
After refueling, ensure that the cap tighten
securely.
Never use the lock-function on the gasoline gun,
when refueling.
Do not smoke while refueling.
Never refuel inside a building or where gasoline
fumes may get in contact with an ignition source.
Keep gasoline and engine away from appliance,
pilot lights, barbecues, electric appliances, power
tools, etc.
If the fuel tank has to be drained, this shall be done
outdoors
Maintenance and storage
The engine shall be stopped when carrying out
maintenance and cleaning operations, when
changing tools and when being transported by
means other than under its own power.
Check regularly that all bolts and nuts are
tightened. Retighten if necessary.
The engine must be completely cooled before
storing indoors or covered.
If the machine unused for a period of time, please
refer to the instructions in this manual.
Maintain or replace safety and instruction labels, as
necessary.
Only use original spare parts or accessories. If not
original parts or accessories is used, the liability is
no longer applied.
Miscellaneous
The gears are delivered pre-greased. However,
always ensure they are well greased before each
use.
Factory-fitted control devices, such as the handle-
mounted cable, must not be removed or exposed.
Only drain the fuel tank outdoors. Gasoline is
extremely flammable and the fumes are explosive.
Ensure that the machine is properly secured when
transported on a flatbed etc.

Identification of the parts

Se Fig. 1 and illustration:
1. Trimmerhead
2. Gear lock
3. Bevel gear
4. Blade guard
5. Shaft/tube
6. Handlebar clamp
7. Handlebar
8. Right handle
9. Throttle trigger
10. Start/Stop switch
11. Safety switch
12. Spark plug cover
13. Recoil starter handle
14. Primer bulp
15. Fuel tank
16. Choke arm
17. Screw for air filter
18. Anti-vibration cover
19. Suspension plate for harness
20. Left handle
21. Nut
22. Bottom plate
23. Washer
24. Blade
25. Top plate
26. Harness

Assembly

Follow the procedure shown in Fig. 2 - 4:
1. Attach the handle to the bracket and lock it with the
handle clamp (Fig. 2).
2. Mount the blade guard (Fig. 3) og and fix it to the
bracket using the supplied bolts.
3. Mount the guard extension to the main blade guard
(Fig. 4).
4. Make sure the brush cutter has a good balance
and that all bolts are tighten.

Mounting the blade and trimmerhead

On the bevel gear there is a small bolt (Fig. 5), which
can lock the gear. It is activated by pulling the bolt, turn
it 45 degrees and release it into position.
When this is done, the blade/trimmerhead cannot turn
around, and it is now possible to release/tighten the
blade and trimmerhead.
Mounting the blade
1. Activate the gear lock bolt (Fig. 5), so it cannot turn
around.
2. Mount the blade (B), washer (C), buttom plate (D)
and nut (E) in correct order, as shown in Fig. 6.
Make sure the blade (B) fits perfectly on the top
plate (A).
3. Tighten the nut (A) securely (link thread)
4. Deactivate gear lock bolt to release the gear again.
Mounting the trimmerhead
1. Activate the gear lock bolt (Fig. 5), so it cannot turn
around.
2. Mount the washer (B) and trimmerhead (A) as
shown in Fig. 7.
3. Tighten the trimmerhead (B) securely with your
hand (link thread)
4. Deactivate gear lock bolt to release the gear again.
Always remember to deactivate the gearlock
before the engine is started!
Notice: Store the individual parts for trimmerhead or
blade for later use.
To dismount the blade/trimmerhead, follow above
instructions in opposite order.
13