Wonder INFLATOR DIGITAL Benutzerhandbuch Seite 10

GENERaLI WaRNINGS
• The inflator gauge shuts off automatically after a certain period of inactivity.
• In the case of first use, prolonged non-use or after transport, inflate
and allow the pressure gauge to switch off at atmospheric pressure.
• Transient pressures may be shown on the display instead of dashes during
inflation/deflation. This does not affect the accuracy of the reading once it
has been stabilised.
• The inflator gauge is ideal for use on valves equipped with a pressure
measurement sensor (TPMS).
• When inflating, maintain a safe distance from the tyre to avoid damage from
accidental tyre bursting.
• It is not recommended to lock the handle in the inflation position, as this
would result in an uninterrupted flow of gas to the tyre, which could cause
the tyre to explode.
• Check that the pressure delivered by the compressor is higher than the
pressure recommended by the tyre manufacturer.
• Ensure that air or nitrogen supplied by the compressor passes through a
separator filter to prevent liquids (e.g. hydrocarbons) and other impurities
from entering the instrument, causing oxidation of internal components and
damages to the measuring system.
• It is recommended not to leave the instrument in the measuring position for
long periods under pressure. As long as the inflator gauge detects a stable
pressure from the tyre, the display will remain active - up to a time limit
beyond which it will switch off.
• The inflator gauge is designed to measure maximum pressures within the
measuring range.
• The highest measurement accuracy is in the temperature range between 15°
and 25°C.
• Avoid shocks; do not disassemble.
• Do not expose to prolonged exposure to weather or sunlight; avoid sudden
temperature changes.
• Do not immerse in water or cleaning products: use a damp cloth to clean
the instrument.
• Do not use to inflate or check the pressure of water-ballasted tyres or contain
anti-puncture products.
• Avoid contact with solvents and hydrocarbons.
• Periodically check that the air filter from the compressor is working properly.
• Keep the device, its accessories and packaging elements out of the reach
of children.
• Disposal must be carried out in accordance with local regulations for
environmental protection and waste disposal. Please note that batteries
must be disposed of separately from the product in accordance with current
regulations.
• Do not attempt to inflate the tyre if the inflator gauge is not connected to the
compressor: this will cause the tyre to deflate.
• We recommend the use of original Wonder accessories.
• Only personnel approved by Wonder are authorized to carry out repairs.
• 12 months warranty, applicable subject to the integrity of the seals.
Wonder does not carry out repairs on instruments more than 5 years after
the date of manufacture and does not accept for examination and repair
instruments with missing parts or on which attempts of disassembly or
modifications have been made.
18
aCCESSORIES
• Spare hose (150 cm) no. 1961 for standard valves
• Spare hose (300 cm) no. 1961/3 for standard valves
(option on request)
baTTERY REPLaCEMENT (see page 6)
Follow the instructions given to replace the two CR2450 3V batteries.
20. Remove the rubber protector.
21. (A/B) Carefully remove the transparent glass by lifting it from the top at the
two attachment points, taking care to keep the inner seal in place.
22. Turn the central part of each of the two battery holders anti-clockwise at
the slot.
23. Remove the old batteries and replace them with new ones, paying attention
to the direction of insertion.
24. Replace the lid of the battery holders and close them by turning them
clockwise at the slot.
25. (A/B) Once both batteries have been replaced, refit the glass, ensuring that
the seal edges remain in the seat of the glass and are compressed all the
way around. Reposition the protector.
SOFTWaRE VERSION VERIFICaTION
Remove the protector and transparent glass as described in section 20 and
21 (A/B). Switch on the pressure gauge and slightly connect the two pins
indicated by the label visible in the picture 22 of the previous section, using
a clean flat head screwdriver for contact. The software version number will
appear on the display once the connection is made.
TECHNICaL SPECIFICaTIONS
• Measurement range: 0.5 ÷ 12 bar | 50 ÷ 1,000 kPa
• Instrument resolution: 0.01 bar | 10 kPa
• Operating temperature: -10°C ÷ 40°C
• Maximum airflow: 66 m
/h a 10 bar | 1,000 kPa
3
• Maximum network pressure: 16 bar | 1,600 kPa
• Level of protection from external agents: IP 55, exceeding the requirement
of EN 12645:2014
19