Exsys EX-60212 Handbuch

HARDWARE INSTALLATION
Please note the following installation instructions. As there are major differences between PCs, we
can only provide you with general instructions for installing the EX-60212. If in doubt, please consult
the manual for your computer system.
1. Switch off your computer and all connected peripheral devices and unplug all devices from the
mains.
2. Loosen the housing screws on the back of your computer and carefully pull off the housing.
3. Now locate a free PCI Express slot (x2 or larger) and carefully insert the card into the selected
PCI Express slot. Make sure that the card is seated correctly and that there is no short circuit.
4. Then secure the card to the housing with a screw.
5. Now close the computer housing with the previously removed screws.
DRIVER INSTALLATION
Windows / Linux / Unix
Once the hardware installation is complete, the operating system will automatically detect and
install the card. If the drivers are not installed automatically, they can be downloaded from the
EXSYS website (www.exsys.de / www.exsys.ch). Enter the article number in the search field
and select the appropriate article. Under 'Downloads' you will find the current driver as a ZIP
file. Once you have extracted the driver folder to your computer, run 'Autorun.exe'. Follow the
installation instructions to complete the installation.
Important! Reboot your PC/Server after installation.
CHECK INSTALLED DRIVER
Open the >Device manager<. Now you should see at „Network adapters" the following new
entries:
If you see these or a similar informations the device is installed correctly.
5
Germany: Switzerland: Italy:
EXSYS Vertriebs GmbH EXSYS Vertriebs GmbH EXSYS Italia Srl
Industriestrasse 8 Dübendorfstrasse 17 Via Belvedere, 45/B
61449 Steinbach 8602 Wangen I-22100 Como
www.exsys.ch www.exsys.it
www.exsys.de
6
Anleitung
Vers. 1.0 / 25.10.24
AUFBAU
2x RJ45 Anschluss Status LEDs pro Anschluss
BESCHREIBUNG & TECHNISCHE DATEN
Die EX-60212 ist eine 2.5 Gigabit Ethernet Karte mit zwei RJ45 Ports für den PCIe Bus. Sie
unterstützt Half- und Full-Duplex sowie Auto-Negotiation zur automatischen Anpassung an die
Geschwindigkeit im Netzwerk (10/100/1000/2500 Mbit/s). Die Bandbreite des PCI-Express Bus
ermöglicht es, an beiden Ethernet-Ports gleichzeitig die volle Leistung von 2.5 Gbit/s zur
Verfügung zu stellen.
Kompatibilität: PCI-Express x2 bis x16
Betriebssysteme: Windows 10/11 (32-bit/64-bit), Linux
Anschlüsse: 2x RJ45 2.5 Gigabit Ethernet Anschluss
Lieferumfang: EX-60212, Low Profile Bügel, Anleitung
ANSCHLÜSSE & LEDS
RJ45 Anschluss:
RJ45 Anschluss
Pin Signal Pin Signal
1 BI_DA+ 4 BI_DC+
2 BI_DA- 5 BI_DC-
87654321
3 BI_DB+ 6 BI_DB-
Status LEDs:
LED Name Farbe
Gelb:
Gelb
Speed Grün:
Grün
Aus:
Steady on: Verbunden
LINK (ACT) Grün
Blinking:
1
EX-60212
Pin Signal
7 BI_DD+
8 BI_DD-
LED Funktion
2.5 Gbps
1000 Mbps
10/100 Mbps
Datenübertragung