Werbung
Quicklinks
RADIO CONTROL MODEL
R/C FLUGMODEL
SPECIFICATIONS
Wingspan
Length
Flying weight
Electric Motor
Glow Engine
Radio
5 Channel / 5 Servos
Technische Daten
Spannweite
Länge
Fluggewicht
Elektroantrieb
Verbrennerantrieb
Fernsteuerung
WARNING! This radio controlled model is NOT a toy. If modified or flown carelessly it could go out of controll and
cause serious human injury or property damage. Before flying your airplane, ensure the air field is spacious enough.
Always fly it outdoors in safe areas and seek professional advice if you are unexperienced.
ACHTUNG! Dieses ferngesteuerte Modell ist KEIN Spielzeug! Es ist für fortgeschrittene Modellflugpiloten bestimmt,
die ausreichende Erfahrung im Umgang mit derartigen Modellen besitzen Bei unsachgemäßer Verwendung kann
hoher Personen- und/oder Sachschaden entstehen. Fragen Sie in einem Modellbauverein in Ihrer Nähe um
professionelle Unterstützung, wenn Sie Hilfe im Bau und Betrieb benötigen. Der Zusammenbau dieses Modells ist
durch die vielen Abbildungen selbsterklärend und ist für fortgeschrittene, erfahrene Modellbauer bestimmt.
BUILDING INSTRUCTIONS / MONTAGEANLEITUNG
1580mm
1160mm
2700g
700 Watt
7.5cc 2T / 11cc 4-T
1580mm
1160mm
2700g
700 Watt
7.5cc 2T / 11cc 4T
5 Kanal / 5 Servos
MITSUBISHI A6M5
"ZERO"
VQAO14 Gray
VQAO15 Green
VQAO151 White
Werbung
Verwandte Anleitungen für VQ Models VQAO14 Gray
Inhaltszusammenfassung für VQ Models VQAO14 Gray
- Seite 1 VQAO14 Gray RADIO CONTROL MODEL VQAO15 Green VQAO151 White R/C FLUGMODEL BUILDING INSTRUCTIONS / MONTAGEANLEITUNG SPECIFICATIONS MITSUBISHI A6M5 Wingspan 1580mm Length 1160mm Flying weight 2700g Electric Motor 700 Watt “ZERO” Glow Engine 7.5cc 2T / 11cc 4-T Radio 5 Channel / 5 Servos...
-
Seite 2: Optional Accessories / Benotigtes Zubehor
OPTIONAL ACCESSORIES / BENOTIGTES ZUBEHOR 10.5x6 for .40 - 2 cycle engine Extension for aileron 11x6 for .46 - 2 cycle engine servo, retract servo. 12x6 for .60 - 4 cycle engine 12x7 for .70 - 4 cycle engine 13x6 for Brushless Motor ESC-60A Retract landing gear VQAR04... - Seite 3 Bottom view 1- Retract landing gear / Fahwerk Ansicht von unten Trial fit the push rod into the wing. Join the pushrod to the retract gear arm and trial fit the retract into the wing. 3x12mm screw 3x12mm schraube After checking that the retract works smoothly, fix the retract on the wing with 3x12mm screws Retract pushrod Fahrwerkanlenkgestange...
- Seite 4 4- Servo mount / Servohalterung Retract servo mount (plywood A,B,C) Einziehfahrwerk servohalterung FWU1 Schneiden Sie etwas Folie weg Cut away only FWU2 the covering CENTER FWU2 WING FWU1 SECTION BOTTOM Install the retract servo onto the retract 5- Retract servo / Einziehfahrwerk servo servo mount and secure it in place with four screw (included with radio set).
- Seite 5 7- Electric retract landing gear / Einziehfahrwerk ELECTRIC RETRACT LANDING GEAR EXTENDED POSITION RETRACTED POSITION ELECTRIC RETRACT LANDING GEAR GEAR RECEIVER Bottom view /Ansicht von unten 8- Fixed gear / Starres Fahrwerk 3x20mm Main landing gear 3x12mm screw Nylon gear strap ..8 3x20mm screw...
- Seite 6 10- Fixed gear / Starres Fahrwerk Bottom view /Ansicht von unten 2x6mm screw ..4 4mm collar ...2 ..2 Bottom view /Ansicht von unten 11- Engine mount / Motoreinbau ! Align the mark on both mounts 5/32x1” Blind-nut with the mark on the fuselage 4x25mm screw ....4 ...4...
- Seite 7 12- Four-stroke engine / 4T Motor 3.2mm 3x25mm screw 3x25mm screw .....4 Nut....4 106~108mm 106~108mm ! Engine thrust on balk head is already adjust at factory Sturz und Zug beachten! FRONT-VIEW Vorderansicht TOP-VIEW Draufsicht 13 Two-stroke engine / 2T Motor 4-13/64”...
- Seite 8 Plywood motor 15- Electric motor/Elektromotor mounting plate (2pcs) - Using a plywood motor mounting plate as a template, mark the fire wall where the four holes are to be drilled (1). - Remove the plywood motor mounting plate and drill a 13/64”(5mm) hole through the fire-wall at each of the four marks marked (2).
- Seite 9 17- Vertical-Horizontal Stabilizers / Hohenleiwerk - Seitenleiwerk Plastic control horn ! Securely glue together ......3 Cut away only If coming off during fly, the film both side you lose control of your Plastic back plate air plane......3 2x12mm screw Cut away only .......6 the film both side...
- Seite 10 19 Tail gear cover 2x10mm screw (5 min.) ..X4 Place the rudder on the trailing edge of vertical stabilizer as show (make sure the rudder move freely without binding) . Mark the mounting hole position with a pencil. Remove the rudder and drill 2mm hole as show.
- Seite 11 BOTTOM VIEW Unteransicht 22- Linkages / Alenkungen Elevator rod Elevator rod Rudder rod Connector To elevator servo To rudder servo 23- Battery / Akku FRONT-VIEW Vorderansicht Securely install the battery, ensuring it will not come loose or rattle during flights. 24- Control Surface / Ruderausschlage 15/64 ~ 5/16”...
- Seite 12 26- Decor / Aufkleber E-141 VQAO14 Gray VQAO151 White VQAO15 Green Note: Cut out the stickers and apply them in the proper area. Do not peel the backing paper off all at once. Peel off one corner of the backing and cut off with scissors. Arrange sticker on model and when satisfied adhere the corner without backing.