Werbung
Verfügbare Sprachen
Verfügbare Sprachen
EN
base plate (T1), figure 73, generally the central plate of the semi-
circle so that the skimmer opening is on the same side.
Important: Insert the wall into the sections, checking that they are
securely inserted into the PCA section grooves, figure 75. Check
that the transition sections are correctly positioned, figure 76. To
prevent the pool wall from falling inwards, attach with tape to the ver-
tical columns (1), figure 77. You can also position the upper plate (5)
fixing the strip, figure 78.
Complete the circle of the wall and make sure the holes are aligned
then fix with screws. Remembering that the screw heads must be on
the inner side of the wall and the washers and nuts on the outside,
figure 79 to 83.
Using a strip of PVC, cover the bolt heads on the inside of the pool
wall to protect the liner from rubbing against objects, which is the
main cause of tears in the liner (fig. 16). This tape must adhere firm-
ly, if it's necessary,
use
PVC glue. Stick the strip with glue for PVC to
insure that for instance the screws are completely covered before
moving on to the next step. Figure 15
If you use no floor insulation
Cover the inside bottom border of the circle using clean thin sifted
sand free of any stones or foreign objects with a height of 1 - 2 cm
and condense this. Press the sand into a vertical triangular shaped
layer that covers the sections and the inside part of the metal wall.
The height of this triangular layer must be around 7 cm. In this way,
you will prevent the liner from sliding under the metal wall and being
damaged due to the pressure and the weight of the water. To avoid
running away of the sand, you should install as shown below, in ad-
dition a plastic sheet along the pelvic floor.
Figure 17
1) chamfer
2) tape
3) platic film
4) steel jacket
Figure 18
If you use floor insulation
Here you can use our optional Styrofoam wedges. These are glued
with an adhesive force on the round floor insulation along the pool
wall.
Alternatively, you can also make the furrow of sand.
Regardless how you make the groove, you have to apply to the floor
insulation and the fillet a swimming fleece because otherwise the
bottom of the pool liner insulation deprives the plasticizers, the film
becomes brittle and thus significantly reduces the lifetime.
Installation of the swimming pool liner
The liner used has been developed to withstand exposure to heat
and ultraviolet rays for a long period of time.
Therefore, under certain climates and conditions of use, the liner
quality can vary slightly.
Never walk on the liner with shoes on.
The liner is the most important and delicate part of the swimming
pool. Do not use knives or any sharp objects to open the swimming
pool bag/container. Carefully separate the liner from the rest of the
parts and keep it in a safe place to avoid undesired holes or damag-
es that could be caused by the tools or the metal wall.
Install the liner on a sunny day, minimum 20º C, so that it can easily
stretch during the installation. It is made of a highly flexible vinyl ma-
terial.
1. Place the liner (L) in the center of the swimming pool and unfold it
towards the sides. Place the rough side towards the inside of the
pool. The welded part that joins the base of the liner with the side
Nuovo deluxe oval | 2013_V1
must perfectly match the lower sections and the wall, all around
the inside perimeter at the bottom of the swimming pool. Figure 19
2. Locate the side welding so that it is perfectly right and perpendicu-
lar on the ground. This will help you to place the liner without folds.
3. Lift the side of the liner that covers the upper edges of the swim-
ming pool and fasten it to the top of the wall with clothespins. Re-
move the wrinkles by pulling smoothly outwards and adjust the lin-
er. Flatten the pool liner with your hands. Don't pull too hard. Figu-
re 20
4. It is very important, that the liner is centered, well extended and
not wrinkled. Start filling the pool with water, but not more than 2-3
cm and work out all the wrinkles and smooth the liner to the wall.
Dont't strech the liner too much. Now make sure the pool wal lis
level. If the level is off by more than 25 mm across the diameter of
the pool, empty the pool, take the wall apart and level the founda-
tions again. Figure 21
5.
Insert the U-profiles (Poolcoping) around the edges of the pool. Af-
ter the U-profiles are installed, cut the last profile to the appropriate
length.
Figure 22 and 23
6.
Now install the white profiles
PL. Leave a gap between the vertical pillars of + / - 10 mm be-
tween the profiles
PCA. Figure 31 and 32
Installation of the decorative foil (optional)
Now put on the decorative film on the steel jacket and make sure
that there are no wrinkles.
Now you have to cut in the steel casing prepunched outlets for
skimmer and inlet ring all around about 2 inches larger.
Figure 25 and 26
Installation of upper section (PCS)
Install the upper section (PCS) on top oft he protective section (PL)
around the entire pool perimeter, figure 84.
Mark and cut off the protector surplus, figure 85 and 86. To prevent
the pool wall from falling inwards, place the upper plate (5) on the
central columns (1) figure 87.
Assembly of vertical sections (VER), Figure 88
Distribute the vertical sections (stayer) around the pool and place
plate T2 onto the upper part of the pool, centre photo.
Align the lower part of one of the vertical sections (VER) with the two
small tabs (tongues) on the base plates (T1). The tabs must be on
the inside of the vertical section.
Align the openings (holes) for positioning screws TO2, on either side
of the vertical section, making sure that they attach to the holes in
the T1 plate tabs, figure 89 and 90.
Place an upper section (T2) onto the top edge of the pool and on a
vertical column (VER), with the tabs on the inside of the section, fig-
ure 91.
Align the openings (holes) for positioning screws TO2 in the three
holes in the vertical section, making sure they fit into the T2 tab
holes, figure 92.
Repeat steps a, b, c, and d in the other sections around the pool.
Assembly of horizontal profiles (handrail)
Install the upper sections HOR1, (straight cut) above columns, plac-
ing their ends on the upper plate (5) and using hole A (Figure 97),
see 93 and 94. Insert and tighten, but not much, screws 13. Pool
models 550x360 do not have this upper section; so in this case you
start with section HOR2, (with a point).
Position all the upper sections HOR2, (with a point) above columns 1
and the other end on plate T2, photos 95 and 96. Align the holes, in-
sert and tighten, but not too much, screws TO2.
Place all the upper sections HOR3 onto T2 plates, figure 98. Align
the holes, insert and tighten, but not too much, screws TO2.
Adjust the upper sections until they are together but not on top of
each other. Tighten the screws, figure 99.
(PCA)
on the circumferential profiles
Page 9 of 51
Werbung
