Steinbach Nuovo deLuxe Bedienungsanleitung Seite 10

EN
Important: If any of the vertical columns (VER) is not straight, adjust
by gently tapping the base plate using a hammer on a piece of
wood. The upper part of the vertical support is optionally set as well.
Mounting of the decorative panels
Align the top connectors with the ends of two upper sections. Hook
the trim underneath the internal edges of the upper section
100) and pull towards you (Figure 101), hooking the trim onto the ex-
ternal part, figure 102.
Installation of the inlet nozzle and skimmer
Also note the information in the description of the skimmer.
Continue filling your pool.
Keep on filling the swimming pool with water until 5 cm below the
cutted inlet nozzle.
Scan the circle in the pelvic wall and make a cross-section with a
sharp knife (Stanley knife), without cutting out beyond the punching
out! Figure 27
Insert the inlet nozzle with a seal of the tank wall inside through to
the outside. The resulting film triangles on the outside should be cut
off along the nozzle clean and accurate.
Now bring on the second seal on the outside of the inlet nozzle and
screw it together with the plastic nut. Tighten the inlet nozzle orderly
(Caution: do not overtighten!).
Figure 28
1) seals
2) steel jacket
3) swimming pool liner
If your inlet nozzle should be equipped with a loose pump connec-
tion piece, it is necessary to seal the threads with Teflon tape!
After placing the inlet nozzle properly, keep on filling the swimming
pool with water until 5 cm below the skimmer.
First, plug the skimmerflap into the skimmercase. Depending on the
design of the skimmer there are 2 seals individually or 1 lip seal in-
cluded.
Assembly with two skimmer seals
Take the skimmer flange and a seal and plug one screw at each top
on the right and left. Now scan the both openings in the foil and the
corresponding holes from the steel wall and pierce them through
with a pointed end. Plug the two screws with the skimmer flange and
the seal from the inside through to the outside and put on the second
seal on the two screws on the tank wall outside. Now onto the pool
wall outside the skimmer has to be fixed with the two screws. As a
result, the remaining holes are punched in the foil and pushed
through the separately screws and bolt together with the skimmer
case. Be sure that the skimmer seals are mounted even all round.
Tighten the screws diagonally and evenly to ensure tightness. The
tightening of the screws may only be done by hand, because not to
overtighten the screws (don't use a cordless screwdriver). As a re-
sult, the film square is cut with a sharp knife (Stanley knife) within
the skimmer flange. Figure 29
Assembly with V-shaped skimmer seal
Replace the lip seal on the skimmer section. Note the flange holes!
Proceed the same as previously described above.
Figure 29
1) steel jacket
2) swimming pool liner
3) seals
4) skimmer flange
Page 10 of 51
After connection to the filter
mately half the
If your skimmer should be equipped with a loose pump connection
piece, it is necessary to seal the threads with Teflon tape!
(Figure
End of season
At the end of the season decrease the water level just below the
skimmer opening or inlet nozzle of the pool. In addition, the connect-
ing tubes to the filter plant have to be dismantled. The filter system
or filter pump is drained by opening the drain plugs. Filter systems
located outdoor must be accommodated in a frost-fre room in the
winter.
We recommend a winterization only when the water temperature is
below 12 degrees.
Damage caused by freezing isn't covered by warranty!
Steinbach VertriebsgmbH,
Aistingerstrasse 2, 4311 Schwertberg, Österreich
FR/IT/CZ/HU/HR/SK/SLO/RO/BG/TR: +43 (0) 7262 / 61431-0
e-mail: service@steinbach.at
www.steinbach.at
system, the water is filled to approxi-
skimmer. (Figure 30)
Nuovo deluxe oval | 2013_V1