Cleaning And Maintenance; Declaration Of Conformity (Doc) - Eurochron EFP 505 Bedienungsanleitung

clEaNINg aNd maINTENaNcE

a) general
Besides the occasional battery change, the product is maintenance-free for you.
-
Maintenance or repair work may be performed only by qualified personnel or
a specialised repair shop. There are no product components which have to be
maintained. For this reason, never open it (except for inserting/changing the
batteries, as described in these operating instructions).
A clean, dry, soft cloth for cleansing purposes is sufficient.
-
Do not press too hard on the transparent cover of the clock-face as this may
cause scratch marks.
The same applies when cleaning the projector lens; also here scratch marks can
result in a blurred projection of the image.
Dust is easily removed by means of a clean, long-haired and soft brush or a
-
vacuum cleaner.
m
In no case should you use abrasive cleaning agents, cleaning alcohol or oth-
er chemical solutions, since these could damage (discolour) the housing or
even impair operation.
b) changing the batteries
If the projection clock is powered by batteries (and not by the power adapter pro-
-
vided), a battery replacement is required when the hands for the time no longer
travel.
If the projection clock is powered by the power adapter provided, the batteries
-
are only used as a backup in case of a power failure. In this case we recommend
replacing the batteries with new batteries periodically about every 2 years, to
avoid battery leakage due to overage.
If the projection clock is not powered by the power adapter, then a battery
-
change triggers the attempt to begin with the detection of the DCF signal, see
chapter „Getting started".
dISPOSal
a) general
The product does not belong in the household waste bin!
Once the product becomes unusable, dispose of it in accordance with the
relevant statutory regulations.
Remove the inserted batteries and dispose of it separately from the pro-
duct.
b) batteries and Rechargeable batteries
As the end user, you are required by law (Battery Ordinance) to return all used bat-
teries and rechargeable batteries; it is not permitted to dispose of batteries with
normal household waste.
Batteries/rechargeable batteries containing hazardous substances are la-
belled with this symbol to indicate that disposal in domestic waste is prohi-
bited. The designations for the heavy metals involved are: Cd = Cadmium,
Hg = Mercury, Pb = Lead.
Used batteries, rechargeable batteries and coin cells can be returned to collection
points in your municipality, our stores or wherever batteries/rechargeable batteries/
coin cells are sold.
You thereby fulfil your statutory obligations and contribute to the protection of the
environment.

dEclaRaTION OF cONFORmITY (dOc)

We, Conrad Electronic SE, Klaus-Conrad-Straße 1, D-92240 Hirschau, hereby declare
that this product conforms to the fundamental requirements and other relevant
regulations of the 1999/5/EC directive.

You can find the declaration of conformity for this product at:
www.conrad.com
TEcHNIcal daTa
a) Projection clock
Power supply ............................... 2x batteries of type AAA/Micro and/or via AC adapt-
er provided (3 V/DC, 100 mA)

In battery mode, continuous projection of time is not possible; however, a
momentary projection is possible by pressing a button briefly.
Alarm mode ................................ yes
Snooze mode ............................... yes
Projection distance .................... approx. 0.4 m to 4 m (focus can be adjusted)
Ambient conditions .................... Temperature -5 °C to +55 °C, air humidity 10% to
95% relative, non condensing
Dimensions .................................. 115 x 83 x 51 mm (W x H x D)
Weight ........................................... 131 g
b) Power adapter
Operating voltage ....................... 230 V/AC, 50 Hz
Output ........................................... 3 V/DC, 100 mA
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.
com). All rights including translation reserved. Reproduction by any method, e.g. photocopy, mi-
crofilming, or the capture in electronic data processing systems require the prior written approval
by the editor. Reprinting, also in part, is prohibited. This publication represent the technical status
at the time of printing.
© copyright 2015 by conrad Electronic SE.