Radio Interference; Information Regarding Article 33 In Reach - Atlas Copco Mwr-Kit Sicherheitshinweise

Safety Information
Designated Standards applied:
BS EN 300220-1 v3.1.1, BS EN 300220-2
v3.2.1, BS EN 301489-1 v2.2.3, BS EN
301489-3 v2.1.1, BS EN 50581:2012, BS EN
55032:2015 + AC:2016 + A11:2020 + A1:2020,
BS EN 55035:2017 + A11:2020, BS EN
61000-3-2:2019 + A1:2021, BS EN
61000-3-3:2013 + A1:2019 + A2:2021, BS EN
61010-1, BS EN 62311:2008
Authorities can request relevant technical information from:
Product Compliance Engineer, Atlas Copco BLM srl., Via
Guglielmo Pepe 11 - 20037 Paderno Dugnano - Milano - Italy
Stockholm, 1 November 2022
Lars Eklöf, Managing Director
Signature of issuer
Authorised Representative UK
James McAllister, General Manager
Atlas Copco Ltd
Swallowdale Lane
Hemel Hempstead
Hertfordshire HP2 7EA
RF Exposure Statement
This portable transmitter has been tested and found to comply
with FCC General Population RF Radiation Exposure limits
set forth for an uncontrolled environment and meets the FCC
radio frequency (RF) Exposure Guidelines. The antenna used
for this device must not be co-located or operating in conjunc-
tion with any other antenna or transmitter.

Radio interference

This is a class A product. In a domestic environment this
product may cause radio interference.

Information regarding Article 33 in REACH

The European Regulation (EU) No. 1907/2006 on Registra-
tion, Evaluation, Authorization and restriction of Chemicals
(REACH) defines among other things requirements related to
communication in the supply chain. The information require-
ment applies also to products containing so called Substances
of Very High Concern (the "Candidate List"). On 27 June
2018 lead metal (CAS nr 7439-92-1) was added to the Candi-
date List.
In accordance with the above this is to inform you that certain
electrical components in the product may contain lead metal.
This is in compliance with current substance restriction legis-
lation and based on legit exemptions in the RoHS Directive
(2011/65/EU). Lead metal will not leak or mutate from the
product during normal use and the concentration of lead metal
4 © Atlas Copco Industrial Technique AB - 9839 1723 00
in the complete product is well below the applicable threshold
limit. Please consider local requirements on the disposal of
lead at product end of life.
FCC and ISED Compliance Statement
This device complies with Part 15 of the FCC Rules. Any
changes or modifications not expressly approved by the man-
ufacturer could void the user´s authority to operate this de-
vice.
Operation is subject to the following two conditions:(1) this
device may not cause harmful interference, and (2) this device
must accept any interference received, including interference
that may cause undesired operation.
The device is only in compliance if no changes or modifica-
tions are made to the device.
The device is in compliance with the requirement for RF ex-
posure in the US with a 5 mm separation distance between the
user and the device - Atlas Copco recommends a separation
distance of 20 cm between the user and the device.
The antenna is fixed to the device and no change in antenna
or fixation of the antenna is acceptable and such modification
is considered to violate the Compliance Statement.
FCC Responsible party:
Name: Rodney Hill
Position: Product Marketing Manager
Address: 3301 Cross Creek Parkway
MI 483 26 Auburn Hills
United States
Mobile: +1 919 272 7837
Email: rodney.hill@us.atlascopco.com
FCC ID: 2AIPFMWRKIT
This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interfer-
ence when the equipment is operated in a commercial en-
vironment. This equipment generates, uses and can radi-
ate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation
of this equipment in a residential area is likely to cause
harmful interference in which case the user will be re-
quired to correct the interference at his own expense.
ISED Compliance Statement:
This device complies with: CAN ICES-1(A)/NMB-1(A)
(English) This device complies with Industry Canada's li-
cence-exempt RSSs. Operation is subject to the following two
conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including inter-
ference that may cause undesired operation of the device.
(French) Le présent appareil est conforme aux CNR d'Indus-
trie Canada applicables aux appareils radio exempts de li-
cence. L'exploitation est autorisée aux deux conditions suiv-
antes:
(1) l'appareil ne doit pas produire de brouillage;
MWR-KIT