Maintenance - Makita 4324 Betriebsanleitung

Finishing edges (Fig. 15)
To trim edges or make dimensional adjustments, run the
blade lightly along the cut edges.
Metal cutting
Always use a suitable coolant (cutting oil) when cutting
metal. Failure to do so will cause significant blade wear.
The underside of the workpiece can be greased instead
of using a coolant.
Dust extraction (Fig. 16)
Clean cutting operations can be performed by connecting
this tool to a Makita vacuum cleaner. Insert the hose of
the vacuum cleaner into the hole at the rear of the tool.
Lower the dust cover before operation.
CAUTION:
Dust extraction cannot be performed when making bevel
cuts.
Rip fence set (optional accessory)
CAUTION:
Always be sure that the tool is switched off and
unplugged before installing or removing accessories.
1) Straight cuts (Fig. 17 & 18 for steel base,
Fig. 19 & 20 for alminum base)
When repeatedly cutting widths of 160 mm or less,
use of the rip fence will assure fast, clean, straight
cuts. To install, insert the rip fence into the rectangu-
lar hole on the side of the tool base with the fence
guide facing down. Slide the rip fence to the desired
cutting width position, then tighten the bolt to secure
it.
2) Circular cuts (Fig. 21 & 22 for steel base,
Fig. 23 & 24 for alminum base)
When cutting circles or arcs of 170 mm or less in
radius, install the rip fence as follows.
Insert the rip fence into the rectangular hole on the
side of the tool base with the fence guide facing up.
Insert the circular guide pin through either of the two
holes on the fence guide. Screw the threaded knob
onto the pin to secure the pin. Now slide the rip
fence to the desired cutting radius, and tighten the
bolt to secure it in place. Then move the tool base all
the way forward.
NOTE:
Always use blades No. B-17, B-18, B-26 or B-27
when cutting circles or arcs.
Anti-splintering device (optional accessory)
(Fig. 25 for steel base)
For splinter-free cuts, the anti-splintering device can be
used. To install the anti-splintering device, move the tool
base all the way forward and insert it between the two
protrusions of the tool base.
CAUTION:
The anti-splintering device cannot be used when making
bevel cuts.
Anti-splintering device (optional accessory)
(Fig. 26 for alminum base)
For splinter-free cuts, the anti-splintering device can be
used. To install the anti-splintering device, move the tool
base all the way forward and fit it from the back of tool
base. When you use the cover plate, install the anti-splin-
tering device onto the cover plate.
CAUTION:
The anti-splintering device cannot be used when making
bevel cuts.
Cover plate (optional accessory)
(Fig. 27 for alminum base)
Use the cover plate when cutting decorative veneers,
plastics, etc. It protects sensitive or delicate surfaces
from damage. Fit it on the back of the tool base.

MAINTENANCE

CAUTION:
Always be sure that the tool is switched off and
unplugged before carrying out any work on the tool.
To maintain product safety and reliability, repairs, mainte-
nance or adjustment should be carried out by a Makita
Authorized Service Center.
ACCESSORIES
CAUTION:
These accessories or attachments are recommended for
use with your Makita tool specified in this manual. The
use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory or
attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita service center.
• Rip fence set
• Hex wrench
• Hose 28-3.0/28-1.5
• Anti-splintering device
• Jig saw blade
Blade type Teeth per inch
No. 51
No. 58
No. 59
No. B-10
No. B-11
No. B-12
No. B-13
No. B-14
No. B-15
No. B-16
No. B-17
No. B-18
No. B-19
No. B-21
No. B-22
No. B-23
No. B-24
No. B-25
No. B-26
No. B-27
No. B-16L
No. BR-13
Cutting length
24 65 mm
8 80 mm
8 80 mm
9 80 mm
9 75 mm
6 80 mm
8 80 mm
18 50 mm
12 50 mm
6 80 mm
6 70 mm
14 45 mm
12 65 mm
12 75 mm
24 50 mm
14 50 mm
32 50 mm
9 75 mm
9 70 mm
24 50 mm
6 150 mm
9 64 mm
9