Using The Saw - EINHELL TC-TS 1200 Originalbetriebsanleitung

•
Mount and fasten the new saw blade in rever-
se order.
•
Caution! Note the running direction. The cut-
ting angle of the teeth must point in running
direction, i.e. forwards (see the arrow on the
blade guard).
•
Close the saw blade guard and screw it in
place with the screws (c). Then fasten the co-
ver plate (32) again with the screws (17).
•
Check to make sure that all safety devices
are properly mounted and in good working
condition before you begin working with the
saw again.
6.5 Sawdust extraction (Fig. 10)
•
The saw is equipped with an extractor port
(16) for chips.
•
This makes it easy to connect to any extrac-
tor.
•
Never use the equipment without the suction
function.
•
Regularly check and clean the suction chan-
nels.

7. Using the saw

7.1. ON/OFF switch (Fig. 1)
•
To turn the saw on, press the green button
"I". Wait for the blade to reach its maximum
speed of rotation before commencing with the
cut.
•
To turn the machine off again, press the red
button "0".
The motor of this equipment is protected against
overload by an overload switch (10).
If the rated current is exceeded, the overload
switch (10) will shut down the equipment.
•
Let the equipment cool down for several mi-
nutes.
•
Press the overload switch.
•
Press the green button „I" to switch on the
equipment.
7.2. Cutting depth (Fig. 1)
Turn the hand crank (8) to set the blade (4) to the
required cutting depth.
Turn anti-clockwise:
larger cutting depth
Turn clockwise:
smaller cutting depth
Anl_TC_TS_1200_SPK1.indb 25 Anl_TC_TS_1200_SPK1.indb 25
GB
7.3. Parallel stop
7.3.1. Stop height (Fig. 2, 11-14)
•
Fit the parallel stop to the saw table by screw-
ing the holder (24) to the table: On the outside
of the table: locking knobs (12) and washer
(b). On the inside of the table: clamping plate
(a). Then use the screws (26) to screw the
stop rail (23) and the holder (24) together.
•
The parallel stop (7) supplied with the bench-
type circular saw has two different guide
faces.
•
For thick material you must use the stop rail
(23) as shown in Fig. 11, for thin material you
must use the stop rail as shown in Fig.12.
•
To change over the stop rail (23) to the lo-
wer guide face you have to slacken the two
knurled screws (26) in order to disconnect the
stop rail (23) from the holder (24).
•
Remove the two knurled screws (26) through
the one slot (27) in the stop rail (23) and in-
sert in the other slot (25).
•
Remount the stop rail (23) on the holder (24).
•
The procedure for changing over to the high
guide face is similar.
7.3.2 Cutting width (Fig. 14)
•
The parallel stop (7) has to be used when
making longitudinal cuts in wooden workpi-
eces.
•
The parallel stop (7) can be mounted on eit-
her side of the saw table (1).
•
The parallel stop (7) can be set to the requi-
red dimension with the help of the scale (22)
engraved on the saw table (1).
•
Tighten the two locking screws (12) in order
to fix the parallel stop (7).
•
Make a trial cut in order to measure the width
before you cut the actual workpiece itself. This
will help you avoid any inaccuracies in the
scale or setting.
7.3.3 Setting the stop length (Fig. 11, 13)
•
The stop rail (23) can be moved in longitudi-
nal direction in order to prevent the workpiece
from becoming jammed.
•
Rule of thumb: The rear end of the stop co-
mes up against an imaginary line that begins
roughly at the center of the blade and runs at
an angle of 45° to the rear.
•
Set the required cutting width
- Slacken the knurled screws (26) and push
the stop rail (23) forward until it touches the
imaginary 45° line.
- Retighten the knurled screws (26).
- 25 -
03.11.2016 08:51:18 03.11.2016 08:51:18