Bosch GCM 10 SD Professional Originalbetriebsanleitung Seite 45

OBJ_DOKU-20077-002.fm Page 45 Tuesday, July 13, 2010 2:24 PM
Extending the Fence (see figure G)
For bevel angles, the fence extensions 19 must
be moved.
– Loosen locking screw 20 and completely pull
out the fence extension 19.
– Retighten the screw again.
Clamping the Workpiece (see figure H)
To ensure optimum working safety, the work-
piece must always be firmly clamped.
Do not saw workpieces that are too small to
clamp.
While clamping the workpiece, do not reach
under the clamping lever of the quick-ac-
tion clamp with your fingers.
– Press the workpiece firmly against the
fence 18.
– Insert the quick-action clamp 21 into one of
the holes 56 intended for this purpose.
– Adapt the quick-action clamp to the work-
piece by turning the threaded rod 58.
– Push on the clamping lever 57 in order to
clamp the workpiece.
Adjusting Horizontal Mitre Angles
To ensure precise cuts, the basic adjustment of
the machine must be checked and adjusted as
necessary after intensive use (see "Checking
and Adjusting the Basic Adjustment", page 51).
Always tighten the locking knob 12 firmly
before sawing. Otherwise the saw blade can
become wedged in the workpiece.
Adjusting Horizontal Standard Mitre Angles
(see figure I)
For quick and precise adjustment of commonly
used mitre angles, detents 15 have been provid-
ed for on the saw table:
Left
0°
15°; 22.5°; 15°; 22.5°;
31.6°; 45°; 52° 31.6°; 45°; 60°
– Loosen the locking knob 12 in case it is tight-
ened.
Bosch Power Tools
– Pull lever 13 and rotate the saw table 16 left
– Release the lever again. The lever must be
Adjusting Any Horizontal Mitre Angle
(see figure J)
The horizontal mitre angle can be set in the
range from 52° (left side) to 60° (right side).
– Loosen the locking knob 12 in case it is tight-
– Pull lever 13 and at the same time push the
– Turn the saw table 16 left or right by the lock-
– Tighten the locking knob 12 again.
Adjusting Vertical Bevel Angles
To ensure precise cuts, the basic adjustment of
the machine must be checked and adjusted as
necessary after intensive use (see "Checking
and Adjusting the Basic Adjustment", page 51).
The vertical bevel angle can be adjusted in a
range from 47° (leftward) to 46° (rightward).
For quick and precise adjustment of commonly
used bevel angles, stops are provided for 0°,
45° and 33.9° angles.
Bevel angle range
– Pull the left fence extension 19 completely
– Loosen the clamping lever 14.
– Tilt the tool arm leftward via handle 5 until
– Hold the tool arm in this position and retight-
Right
or right to the requested detent.
felt to engage in the detent.
ened.
locking bracket 11 until it engages in the
groove intended for this. The saw table can
be moved freely now.
ing knob until the angle indicator 71 indi-
cates the requested mitre angle.
45°– 0
outward. (see "Extending the Fence",
page 45)
the angle indicator 31 indicates the desired
bevel angle.
en the clamping lever 14.
The clamping force of the clamping lever
must securely hold the position of the tool
arm at any bevel angle.
1 609 929 X04 | (13/7/10)
English | 45